Bleeding the Brakes on a 2019 Husqvarna Vitpilen 701
Shop parts for a 2019 Husqvarna Vitpilen 701 Motorcycle.
The Vitpilen 701 runs hydraulic disc brakes at both ends — a single front disc gripped by a radial-mount caliper, plus a rear disc — and it left the factory with an ABS module plumbed into the system. That layout is friendly to a home mechanic: both circuits can be bled at the calipers with ordinary hand tools. The one component you should not attempt to purge yourself is the ABS unit, which needs dealer-level equipment if air ever reaches it.
What follows is a complete fluid flush and air purge, front and rear, in an order that keeps air from being pulled back into the system.
What the 701's Brake Layout Means for This Job
Both wheels are hydraulically actuated, so you have two independent circuits to service. Each has its own master cylinder, reservoir, and caliper, and they share nothing but the fluid specification. Finish one end completely before you open the other.
The ABS hardware sits between the master cylinder and the caliper. A normal bleed at the caliper bleeder pushes fresh fluid through the caliper, the line, and the module's internal passages, which is exactly what routine maintenance requires. What a caliper bleed cannot reliably do is clear a pocket of air trapped inside the ABS pump or valve block. If the reservoir has ever run dry, if a line or the module has been off the bike, or if the lever went soft after the system was opened, stop here and take the bike to a shop that can cycle the pump with a diagnostic tool.
When a Bleed Is Actually Due
Reach for the tools when the front lever or rear pedal feels spongy, when the lever travels closer to the grip than it used to, when the fluid in either reservoir looks dark or cloudy, or after any work that opened the hydraulic system — new lines, caliper service, or master cylinder work.
Even with no symptoms, brake fluid absorbs moisture from the air over time. That moisture lowers the fluid's boiling point, and a boiled fluid creates vapor that behaves exactly like air in the line, which shows up as a lever that goes long under hard, repeated braking. Many riders simply refresh the fluid on a regular interval rather than waiting for a problem to appear.
Tools and Supplies to Gather
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve on each caliper
- Clear tubing that fits snugly over the bleeder nipple
- A small catch bottle for the old fluid
- Rags or shop towels, plus a syringe or turkey baster for emptying the reservoir
- The correct driver for the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder makes the job much easier when you are working alone, since you no longer have to coordinate the lever and the wrench.
Setting Up Before You Open Anything
Get the bike securely upright on a stand so it cannot tip while you are leaning on the bars. Turn the handlebar until the front reservoir sits level, because an angled reservoir will spill as soon as the cap comes off. Then drape rags over the tank area, the plastics, the instrument cluster, and anything else below the reservoir.
Brake fluid attacks paint and plastic on contact, so treat every drip as urgent: wipe it immediately and rinse the area with water. Keep the old fluid in the catch bottle, not on the floor.
Bleeding the Front Caliper
- Clean the reservoir cap and the area around it so grit cannot fall in, then remove the cap and diaphragm.
- Draw most of the old fluid out of the reservoir with the syringe, leaving the bottom covered so no air enters the line.
- Refill with fresh fluid from the sealed container.
- Slip the clear tubing over the bleeder valve and route the other end into the catch bottle, with the bottle positioned so the tubing runs upward before it drops.
- Squeeze the front lever slowly and hold it against the grip.
- Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tubing.
- Close the bleeder before you release the lever. Releasing with the bleeder open draws air straight back in.
- Repeat the squeeze, hold, open, close, release cycle, topping off the reservoir every few cycles so it never drops low enough to suck air.
- Keep going until the fluid arriving in the tubing is clean and free of bubbles, then finish with the lever held and the bleeder closed.
If your bike has two front calipers, bleed each one in turn, starting with the caliper farthest from the master cylinder in terms of hydraulic path.
Bleeding the Rear Caliper
- Open the rear reservoir, remove most of the old fluid, and top it up with fresh fluid.
- Fit the tubing to the rear bleeder and lead it into the catch bottle.
- Press and hold the brake pedal.
- Open the bleeder a quarter turn, let fluid and air escape, then close it before releasing the pedal.
- Repeat, watching the reservoir level and refilling as needed, until the fluid runs clean and bubble-free.
Finishing the Job
Tighten each bleeder snugly with the box-end wrench — firm enough to seal, never so tight that you risk damaging the caliper threads. Fill each reservoir to the level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder and the banjo fittings at both ends for weeping, and pump the lever and pedal a few times to confirm they build pressure.
Testing Before You Ride
Both controls should feel firm and consistent, not spongy, and neither should slowly sink while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Then, in a safe open area, test the brakes at low speed before riding normally.
When to Stop and Take It to a Shop
Bring the bike in if the lever will not firm up after several honest bleeding attempts, if it only firms up after pumping, if bubbles keep appearing no matter how long you bleed, or if you find fluid weeping from a master cylinder or caliper. Any suspicion that air reached the ABS module is also a shop job. On a safety-critical system, knowing when to hand it over is part of the skill.
Related Shopping Categories
Shop Brake Fluid for a 2019 Husqvarna Vitpilen 701 Motorcycle.
Shop Brake Lines for a 2019 Husqvarna Vitpilen 701 Motorcycle.
Shop Brake Pads for a 2019 Husqvarna Vitpilen 701 Motorcycle.
Shop Stands for a 2019 Husqvarna Vitpilen 701 Motorcycle.
Shop Brake Tools for a 2019 Husqvarna Vitpilen 701 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.