A Rider’s Guide to Bleeding 2019 Honda Africa Twin CRF1000L Brakes
Shop parts for a 2019 Honda Africa Twin Motorcycle.The 2019 Honda Africa Twin CRF1000L uses hydraulic disc brakes at both ends and is equipped with ABS. That means the front lever and rear pedal each push fluid through a sealed hydraulic circuit, and both circuits benefit from periodic bleeding. Bleeding does two jobs: it removes air that makes the lever or pedal feel soft, and it replaces old fluid that has absorbed moisture. On a bike like the Africa Twin, which can carry luggage, a passenger, and cover long distances, a firm, consistent brake feel is worth protecting.
When the Africa Twin Needs a Bleed
Air is the usual reason a brake lever feels spongy or pulls closer to the grip than it used to. Air can enter after a line is replaced, a caliper is serviced, the master cylinder is opened, or the reservoir runs low. Fluid condition is the other reason. Brake fluid absorbs moisture over time, which lowers its boiling point and can lead to fade under hard use. Dark or cloudy fluid in the reservoir is a clear sign that fresh fluid is due. Many riders refresh brake fluid on a regular schedule even when the brakes still feel normal, because the change is gradual and easy to overlook.
Tools and Supplies for the Job
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- Clear tubing that fits snugly over the bleeder
- A catch bottle for used fluid
- Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
- Optional: a one-way check-valve bleeder or vacuum bleeder, which can make one-person bleeding easier
Use only fluid from a sealed container, and do not reuse fluid that has been through the system. Brake fluid damages paint and plastic on contact, so keep rags handy before you open anything.
Prepare the Bike and Protect Surfaces
Support the Africa Twin securely upright on a stand. Turn the handlebars so the front reservoir sits level before you remove the cap. Cover the painted bodywork, plastics, instrument area, and any nearby surfaces with rags. If fluid spills, wipe it up immediately and rinse the area with water. Work in a well-ventilated space and keep the reservoir cap and diaphragm clean once they are off the bike.
The Bleeding Procedure
- Open the front reservoir and use a syringe or turkey baster to remove most of the old fluid. Do not let the reservoir run dry, because that draws air into the system.
- Refill the reservoir with fresh fluid of the type marked on the cap, leaving room for the diaphragm.
- Attach the clear tubing to the front bleeder valve and route the other end into the catch bottle. Make sure the tubing fits snugly so air cannot enter around the bleeder.
- Slowly squeeze and hold the front lever. With the lever held, open the bleeder about a quarter turn. Fluid and air will move through the tube.
- Close the bleeder before releasing the lever. This order matters: releasing the lever with the bleeder open can pull air back into the caliper.
- Repeat the squeeze, hold, open, close, and release sequence until fresh, clean fluid comes through the tube with no bubbles. Check the reservoir often and top it off before it gets low.
- If your Africa Twin has two front calipers, bleed each one in turn. As a general practice, start with the caliper farthest from the master cylinder, then move to the closer one.
- Move to the rear hydraulic brake. Open the rear reservoir, remove most of the old fluid, and refill with fresh fluid. Attach the clear tube to the rear bleeder and route it to the catch bottle.
- Press and hold the rear pedal, open the bleeder about a quarter turn, then close it before releasing the pedal. Repeat until the fluid runs clean and bubble-free, keeping the reservoir topped off throughout.
- As you work, watch for fluid weeping at the bleeder threads or around the banjo fittings. A small amount at the bleeder threads can be normal during the open phase, but a steady leak after tightening means you should stop and inspect.
Finish, Test, and Check for Leaks
When clean fluid has come through both circuits, tighten each bleeder snugly without overtightening. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the bike. Check the bleeder valves and banjo fittings for leaks. The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Before riding normally, test the brakes at low speed in a safe area.
Troubleshooting and When to Visit a Shop
If the lever or pedal will not firm up after several bleeding attempts, or if it firms up only after pumping, air is likely still trapped. Persistent bubbles at the bleeder can also point to a seal or fitting problem. Fluid leaking from the master cylinder or caliper is another reason to stop. Because the 2019 Africa Twin has ABS, a standard bleed through the caliper bleeders is generally enough to refresh fluid, but if the reservoir ran dry or the ABS unit or its lines were disconnected, air may have entered the ABS unit itself. That may require a dealer-level procedure or diagnostic tool, so the bike should go to a shop. The same advice applies if you are not confident with a linked-brake system or cannot get a firm lever after repeated attempts.
Related Shopping Categories
Shop Brake Fluid for a 2019 Honda Africa Twin Motorcycle.
Shop Brake Lines for a 2019 Honda Africa Twin Motorcycle.
Shop Brake Pads for a 2019 Honda Africa Twin Motorcycle.
Shop Stands for a 2019 Honda Africa Twin Motorcycle.
Shop Brake Tools for a 2019 Honda Africa Twin Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.