How to Bleed the Brakes on a 2018 Kawasaki Z900 ABS

Shop parts for a 2018 Kawasaki ZR900 - Z900 ABS Motorcycle.

Know Your Bike's Brake Layout First

The 2018 Kawasaki Z900 ABS stops on hydraulic disc brakes at both ends. The front circuit is fed by a master cylinder on the handlebar and works the front caliper or calipers; the rear circuit has its own master cylinder, its own small reservoir, and its own caliper, operated by the foot pedal. The two circuits are completely independent, so each one gets bled on its own, and neither one shares fluid with the other.

Because this machine carries ABS, keep one caveat in mind from the very start. A routine flush through the caliper bleeders is a normal garage job and is exactly what this article covers. But if air has found its way into the ABS unit itself — the reservoir ran dry while you were working, a line was disconnected, or the pump or modulator was disturbed — purging that air may require a dealer-level procedure or a diagnostic tool. Everything below assumes the ABS unit has stayed sealed and you are simply refreshing fluid and clearing air from the lines and calipers.

When a Bleed Is Actually Needed

The classic signal is a lever or pedal that feels soft or spongy, or a front lever that now pulls noticeably closer to the grip than it used to. A pedal that feels long before the brakes bite is the rear equivalent. Dark, cloudy, or gritty-looking fluid in the reservoir is another clear sign, and so is any recent work that opened the hydraulic system: new lines, caliper service, or master cylinder work all introduce air that has to come out.

Even with no symptoms at all, brake fluid absorbs moisture from the air over time. That moisture lowers the fluid's boiling point, which is what allows brakes to fade under hard, repeated use when you need them most. Many riders simply refresh the fluid on a regular schedule rather than waiting for the lever to go soft.

Tools and Supplies to Have on the Bench

  • Fresh brake fluid of the type printed on the master cylinder reservoir cap, poured from a sealed container — an opened bottle has already begun absorbing moisture
  • A box-end wrench that fits the bleeder valve snugly, so it will not round the hex
  • Clear tubing that fits tightly over the bleeder nipple, long enough to reach your catch bottle
  • A small, stable catch bottle
  • Rags or shop towels, plus a spray bottle of clean water
  • A syringe or turkey baster for lifting old fluid out of the reservoir
  • The correct driver for the reservoir cap screws
  • Optional but helpful for solo work: a one-way check-valve bleeder or a vacuum bleeder

Set Up Before You Open Anything

Get the bike secure and upright on a stand so it cannot tip while you are leaning on the lever. Turn the handlebars until the front reservoir sits level, since a tilted reservoir will spill as soon as the cap comes off. Then drape rags over the painted surfaces, the plastics, and the instrument area. Brake fluid damages paint and plastic on contact, so any drip should be wiped up immediately and the area rinsed with water rather than left to sit.

Bleeding the Front Brake, Step by Step

  1. Remove the reservoir cap and the diaphragm beneath it, and set them somewhere clean where they will not pick up grit.
  2. Draw most of the old fluid out of the reservoir with the syringe or baster, but leave a little in the bottom so you do not push air into the master cylinder.
  3. Top the reservoir up with fresh fluid from the sealed container.
  4. Slip the box-end wrench over the bleeder valve, then push the clear tubing onto the nipple and route the other end into the catch bottle.
  5. Squeeze the front lever slowly and hold it against the grip.
  6. Open the bleeder about a quarter turn. Fluid and trapped air will push out through the tubing — watch for bubbles.
  7. Close the bleeder before you release the lever. Releasing with the bleeder open draws air straight back into the caliper.
  8. Release the lever slowly and let it return.
  9. Check the reservoir and top it off again. Repeat the squeeze, open, close, release cycle, keeping the reservoir well above the low mark the whole time.
  10. Continue until the fluid coming through the tubing runs clean and completely bubble-free.
  11. If your bike carries two front calipers, bleed each one in turn. As a general practice, start with the caliper farthest from the master cylinder and work toward the closer one.

Bleeding the Rear Brake

  1. Open the rear reservoir, remove most of the old fluid, and refill with fresh fluid.
  2. Fit the wrench and clear tubing to the rear bleeder and route the tubing to the catch bottle.
  3. Press and hold the brake pedal down.
  4. Open the bleeder a quarter turn, let fluid and air escape, then close it before releasing the pedal.
  5. Release the pedal, top off the reservoir, and repeat until the fluid runs clean and clear of bubbles. Rear reservoirs are small, so check the level often.

Buttoning It Up

When the fluid runs clean at both ends, tighten each bleeder snugly with the box-end wrench. Snug is the goal — do not lean on it, because overtightening can damage the seat. Fill the reservoir to the level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then look closely at the bleeder and at the banjo fittings at the master cylinder and caliper for any weeping or dampness.

Confirm the Job Before You Ride

The lever and pedal should feel firm and consistent, and neither should slowly sink while you hold steady pressure on it. Spin each wheel by hand to confirm the brakes are not dragging. Then, in a safe open area, test the brakes at low speed before riding normally.

When to Stop and Take It to a Shop

If the lever will not firm up after several honest attempts, if it only firms after pumping, if bubbles keep appearing no matter how long you bleed, or if you find fluid leaking from the master cylinder or a caliper, stop and have the bike inspected. The same applies any time air may have entered the ABS unit. Those situations are past what a home bleed can reliably fix.

Related Shopping Categories

Shop Brake Fluid for a 2018 Kawasaki ZR900 - Z900 ABS Motorcycle.

Shop Brake Lines for a 2018 Kawasaki ZR900 - Z900 ABS Motorcycle.

Shop Brake Pads for a 2018 Kawasaki ZR900 - Z900 ABS Motorcycle.

Shop Stands for a 2018 Kawasaki ZR900 - Z900 ABS Motorcycle.

Shop Brake Tools for a 2018 Kawasaki ZR900 - Z900 ABS Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.