Bleeding the Brakes on a 2018 Kawasaki Concours 14 ABS

Shop parts for a 2018 Kawasaki ZG1400 - Concours ABS Motorcycle.

Understand the System You Are Servicing

The 2018 Kawasaki Concours 14 ABS runs hydraulic disc brakes at both ends, and both circuits are supervised by an anti-lock braking system. That gives you two independent hydraulic circuits to look after: a front circuit fed by the master cylinder on the right handlebar, and a rear circuit fed by the pedal master cylinder low on the right side of the machine. Each has its own reservoir, its own line, and its own bleeder at the caliper, and on this model the front and rear circuits work separately, so you can service them one at a time in whichever order suits you.

Because this bike carries ABS, one important limit applies. A routine flush through the caliper bleeders is a normal garage job and is what this article covers. But if air has entered the ABS unit itself — because the reservoir ran dry, because a line or the ABS unit was disconnected, or because the system was opened during other service — the modulator may need a dealer-level procedure or diagnostic tool to purge properly. In that case, stop and take the bike to a shop rather than pumping the lever for an hour.

Signs That a Bleed Is Overdue

Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. Moisture lowers the fluid's boiling point, and a boiling fluid creates vapor in the line that behaves exactly like air — the lever goes soft right when you need braking most. That is why many riders refresh the fluid on a schedule even when nothing feels wrong.

Watch for a lever or pedal that feels spongy rather than solid, a front lever that now comes noticeably closer to the grip than it used to, fluid in the reservoir that has turned dark or cloudy, or a lever that firms up only after a couple of quick pumps. Any of those point to air or degraded fluid. You should also bleed after any work that opened the hydraulic system: new lines, caliper service, or master cylinder repairs.

Tools and Supplies to Collect

  • Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container — opened fluid absorbs moisture, so do not reuse an old bottle
  • A box-end wrench that fits the bleeder valve snugly
  • A length of clear tubing that fits tightly over the bleeder nipple
  • A small catch bottle for the old fluid
  • Rags or shop towels, plus a syringe or turkey baster for lifting old fluid out of the reservoir
  • The correct driver for the reservoir cap screws
  • Optional: a one-way check-valve bleeder or a vacuum bleeder, which makes a one-person job much easier

Set Up Before You Loosen Anything

Get the bike secure and upright on a stand so it cannot tip while you are working the lever. For the front circuit, turn the handlebars until the reservoir on the bar sits level; a tilted reservoir will spill. Lay rags over the tank area, the plastics, the instrument cluster, and anything painted below the reservoir and calipers. Brake fluid attacks paint and many plastics on contact, so wipe up any drip immediately and rinse the area with water if a spill reaches a painted surface.

The Bleeding Procedure, Step by Step

  1. Wipe the reservoir cap and the area around it clean so grit cannot fall in, then remove the cap and diaphragm.
  2. Use the syringe or baster to draw most of the old fluid out of the reservoir. Leave enough to cover the bottom so you do not push air into the master cylinder.
  3. Top the reservoir up with fresh fluid from the sealed container.
  4. Push the clear tubing onto the caliper bleeder and route the other end into the catch bottle, with the bottle positioned so the tube end stays submerged.
  5. Squeeze the front lever and hold it, or press and hold the rear pedal if you are working that circuit.
  6. Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch the reservoir level as it drops.
  7. Close the bleeder fully before you release the lever or pedal. Releasing with the bleeder open draws air back into the caliper.
  8. Repeat the squeeze, hold, open, close, release cycle, topping the reservoir off between rounds so it never runs low enough to pull air in.
  9. Keep going until the fluid coming through the tube is clean and free of bubbles, then close the bleeder and check the lever or pedal feel.
  10. If your bike has two front calipers, bleed each one in turn, finishing with the caliper you have not yet done. As a general practice, start with the caliper farthest from the master cylinder and work toward the closest.

Finishing the Job Correctly

Tighten the bleeder snugly with the box-end wrench — firm enough to seal, never so hard that you risk damaging the caliper threads. Fill the reservoir to the level marking on the body, reinstall the diaphragm and cap, and wipe away every trace of spilled fluid. Then inspect the bleeder and the banjo fittings at the caliper and master cylinder for weeping; a dry joint after a few lever pulls is what you want to see.

Test Before You Ride

The lever and pedal should feel firm and consistent, and should hold that feel when you apply steady pressure for several seconds rather than slowly sinking toward the grip. Spin each wheel by hand to confirm the brakes are not dragging. Then, in a safe open area, test the brakes at low speed before riding normally. If the lever still will not firm up after several rounds of bleeding, if it only firms up when pumped, if bubbles keep appearing, or if fluid is leaking anywhere in the system, stop and have the bike inspected by a professional — especially on an ABS-equipped machine where air may have reached the modulator.

Related Shopping Categories

Shop Brake Fluid for a 2018 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Lines for a 2018 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Pads for a 2018 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Stands for a 2018 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Tools for a 2018 Kawasaki ZG1400 - Concours ABS Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.