Bleeding the Brakes on a 2018 Ducati Scrambler Street Classic
Shop parts for a 2018 Ducati Scrambler Street Classic Motorcycle.
Know Your Bike's Brake Layout Before You Start
The 2018 Ducati Scrambler Street Classic uses hydraulic disc brakes at both ends. The front system runs from a lever-mounted master cylinder to a single caliper on the front wheel, and the rear runs from a pedal master cylinder to its own caliper out back. This model year also carries ABS. That combination means a routine fluid refresh through the caliper bleeders is well within reach of a home mechanic, but it also sets a clear boundary: if air has been pulled into the ABS unit itself — because the reservoir ran dry, or because the ABS block or its lines were opened — the internal valving needs a dealer-level procedure and diagnostic tool to purge properly. Plan your work so that boundary is never crossed.
Why Brake Fluid Needs Replacing at All
Brake fluid is hygroscopic, meaning it absorbs moisture from the air over time. That moisture does two harmful things. It lowers the fluid's boiling point, so hard, repeated braking can generate vapor in the system and give you a lever that goes soft exactly when you need it most. It also encourages corrosion inside the calipers and master cylinder. Because of this, many riders refresh the fluid on a regular interval even when the brakes still feel fine.
Bleeding is also the fix when something has changed. A spongy lever, a lever that now pulls closer to the grip than it used to, a pedal with a mushy feel, or dark, cloudy fluid visible in the reservoir all point to air or degraded fluid. Any job that opened the hydraulic circuit — new lines, caliper service, master cylinder work — requires a bleed afterward before the bike goes back on the road.
Gather These Tools and Supplies
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type.
- A box-end wrench that fits the bleeder valve on each caliper you plan to bleed.
- Clear tubing that fits snugly over the bleeder nipple, plus a catch bottle to hang it in.
- Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir.
- The correct driver for the reservoir cap screws.
- Optional but helpful: a one-way check-valve bleeder or a vacuum bleeder, which makes a solo job much less fiddly.
Set Up So Nothing Gets Damaged
Get the Scrambler securely upright on a stand so it cannot tip while you are working the lever. Turn the handlebar until the front reservoir sits level, since a tilted reservoir will spill as soon as the cap comes off. Then drape rags over the tank area, the plastics, the instrument cluster, and anything else below the reservoir. Brake fluid attacks paint and many plastics on contact, so a spill that sits for even a minute can leave a permanent mark. If a drop does land somewhere, wipe it up immediately and rinse the area with water.
The Bleeding Procedure, Step by Step
- Open the reservoir and use the syringe or baster to draw out most of the old fluid. Leave enough in the bottom that you are not pulling air into the master cylinder port.
- Refill with fresh fluid from the sealed container, keeping the level well up the reservoir.
- Push the clear tubing onto the caliper bleeder and route the other end into the catch bottle, with the bottle positioned so the tubing runs upward away from the bleeder.
- Squeeze the lever and hold it firm against the grip. For the rear, press and hold the pedal.
- With pressure held, open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tubing. Watch the tube, not the reservoir, while it flows.
- Close the bleeder before you release the lever or pedal. Releasing with the bleeder open draws air straight back into the caliper.
- Release, then repeat the squeeze–hold–open–close cycle. Top off the reservoir every few cycles so it never runs low enough to pull air in at the master cylinder.
- Keep going until the fluid coming through the tubing is clean and free of bubbles, matching the fresh fluid you are adding.
- Move to the other caliper if you are bleeding both ends, and work through the same cycle there. As a general practice, start with the caliper farthest from its master cylinder and finish with the closest.
Closing It Out and Checking Your Work
When the fluid runs clean, tighten the bleeder snugly with the box-end wrench. Snug is the goal — do not lean on it, because overtightening can damage the seat and create a leak. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder and the banjo fittings at the caliper and master cylinder for any weeping or dampness.
Test Before You Ride
Pull the lever and press the pedal. Both should feel firm and consistent, and neither should slowly sink while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Then, in a safe open area, test the brakes at low speed before riding normally. If anything feels vague, stop and investigate rather than riding it out.
When to Hand It to a Shop
If the lever will not firm up after several honest attempts, if it only firms after pumping, or if bubbles keep appearing no matter how long you bleed, something else is wrong — a leaking master cylinder seal, a damaged line, or air trapped where a home bleed cannot reach it. Fluid weeping from the master cylinder or caliper is another stop sign. And on this ABS-equipped Scrambler, any suspicion that air entered the ABS unit itself means the bike should go to a dealer. Knowing when to stop is part of doing the job right.
Related Shopping Categories
Shop Brake Fluid for a 2018 Ducati Scrambler Street Classic Motorcycle.
Shop Brake Lines for a 2018 Ducati Scrambler Street Classic Motorcycle.
Shop Brake Pads for a 2018 Ducati Scrambler Street Classic Motorcycle.
Shop Stands for a 2018 Ducati Scrambler Street Classic Motorcycle.
Shop Brake Tools for a 2018 Ducati Scrambler Street Classic Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.