Bleeding the Brakes on a 2017 Kawasaki Z900
Shop parts for a 2017 Kawasaki ZR900 - Z900 Motorcycle.The 2017 Kawasaki ZR900 — sold as the Z900 — uses hydraulic disc brakes at both ends. The front brake is operated by the lever on the right handlebar, and the rear brake is operated by the foot pedal. Some 2017 Z900s are ABS-equipped, so check your bike for an ABS indicator light or tone ring before you begin. On an ABS model, a normal bleed at the caliper bleeders is still the right way to refresh fluid, but if air has entered the ABS unit itself, the bike needs a shop-level procedure. This guide covers both hydraulic circuits; the rear is not a mechanical drum brake, so it is bled rather than adjusted.
When a Bleed Is Due — and Why It Matters
Bleed the Z900 when the front lever feels spongy or pulls closer to the grip than it used to, when the rear pedal feels soft or travels farther than normal, or when the fluid in either reservoir looks dark or cloudy. A bleed is also required after any work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work. Even without symptoms, brake fluid absorbs moisture over time. That moisture lowers the fluid’s boiling point and can cause fade under hard use, so many riders refresh it on a regular schedule. Use the fluid type marked on the master cylinder reservoir cap and use fresh fluid from a sealed container.
Tools and Supplies to Have Ready
- Fresh brake fluid of the type marked on the reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- Clear tubing that fits snugly over the bleeder
- A catch bottle for old fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver that fits the reservoir cap screws
- Optional: a one-way check-valve bleeder or vacuum bleeder for one-person work
Set Up the Bike and Protect the Finish
Support the Z900 securely upright on a stand so it cannot tip while you are working. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Keep the reservoir cap and diaphragm clean and set them aside where they will not pick up grit. Do not let the reservoir run dry at any point; that is the most common way to pull air into the system.
Bleeding the Front Brake Circuit
- Remove the front reservoir cap and diaphragm. Use the syringe or turkey baster to remove most of the old fluid from the reservoir without letting the level drop low enough to draw air.
- Refill the reservoir with fresh fluid of the type marked on the cap. Leave the cap off for now, but keep the reservoir covered with a rag to prevent spills.
- Attach the clear tubing to the front caliper bleeder and route the other end into the catch bottle. If your Z900 has two front calipers, bleed one at a time; start with the caliper farthest from the master cylinder.
- Squeeze and hold the front lever. Open the bleeder about a quarter turn to let fluid and air escape. Close the bleeder before you release the lever. Never release the lever while the bleeder is open.
- Repeat the squeeze-hold-open-close-release sequence until fresh, clean, bubble-free fluid comes through the tube. Check the reservoir level often and top it off so it never runs low.
- If there is a second front caliper, repeat the same sequence on it, keeping the reservoir topped off throughout.
Bleeding the Rear Brake Circuit
- Open the rear reservoir and remove most of the old fluid with the syringe or baster. Refill with fresh fluid of the type marked on the cap.
- Attach the clear tubing to the rear caliper bleeder and route it into the catch bottle.
- Press and hold the rear pedal. Open the bleeder about a quarter turn, let fluid and air out, then close the bleeder before releasing the pedal.
- Repeat until the fluid in the tube is clean and free of bubbles. Keep an eye on the rear reservoir and top it off as needed.
Finishing, Leak Checks, and a Low-Speed Test
When both circuits are bled, tighten each bleeder snugly without overtightening. Fill each reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the bike. Check for leaks at the bleeder and at the banjo fittings. The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Before riding normally, test the brakes at low speed in a safe area.
If the Lever or Pedal Will Not Firm Up
If the lever or pedal will not firm up after several bleeding attempts, or if it firms up only after pumping, stop and diagnose rather than continuing to ride. Persistent air bubbles, fluid leaking from the master cylinder or caliper, or a lever that slowly sinks under pressure all point to a problem that needs attention. On an ABS-equipped Z900, if the reservoir ran dry or the ABS unit or its lines were disconnected, air may be trapped in the ABS unit. That requires a dealer-level procedure or diagnostic tool, so take the bike to a shop. A brake system that will not hold a firm lever is not safe to ride.
Related Shopping Categories
Shop Brake Fluid for a 2017 Kawasaki ZR900 - Z900 Motorcycle.
Shop Brake Lines for a 2017 Kawasaki ZR900 - Z900 Motorcycle.
Shop Brake Pads for a 2017 Kawasaki ZR900 - Z900 Motorcycle.
Shop Stands for a 2017 Kawasaki ZR900 - Z900 Motorcycle.
Shop Brake Tools for a 2017 Kawasaki ZR900 - Z900 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.