Bleeding the Brakes on a 2017 Honda Africa Twin DCT
Shop parts for a 2017 Honda Africa Twin DCT Motorcycle.The 2017 Honda Africa Twin DCT uses hydraulic disc brakes at both ends and is equipped with ABS. The DCT gearbox does not change how the hydraulic system is bled, but the ABS unit does affect what you should do if air gets into the wrong place. A normal bleed at the calipers is the right approach for refreshing fluid and removing air that has collected near the calipers or lines. If the reservoir has run dry, or if the ABS unit or its lines have been opened, the bike should go to a shop with the correct diagnostic equipment.
Why and When the Africa Twin DCT Needs a Bleed
Brake fluid absorbs moisture over time, which lowers its boiling point and makes brake fade more likely during hard or repeated use. Even if the lever still feels acceptable, dark or cloudy fluid in the reservoir is a sign that fresh fluid is overdue. A spongy lever, a lever that pulls closer to the grip than it used to, or a pedal that feels soft are all clues that air or old fluid is affecting the system. Bleeding is also necessary after work that opened the hydraulic circuit, such as replacing a brake line, servicing a caliper, or repairing the master cylinder. On this Africa Twin DCT, treat the front and rear systems as separate hydraulic circuits and bleed each one properly.
Tools and Supplies You Will Need
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- A length of clear tubing that fits snugly over the bleeder
- A catch bottle for the old fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
- Optional: a one-way check-valve bleeder or vacuum bleeder to make one-person bleeding easier
Use only fluid from a sealed container, and do not reuse fluid that has been sitting open. Brake fluid pulls moisture from the air, and contaminated fluid will undo the benefit of the job.
Prepare the Bike and Protect Sensitive Surfaces
Support the 2017 Africa Twin DCT securely upright on a stand so it cannot tip while you are working. Turn the handlebars so the front reservoir sits level before you open it. Cover painted bodywork, plastic panels, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Keep the reservoir cap and diaphragm clean and set them on a clean towel so grit does not fall into the fluid.
The Bleeding Procedure, Front and Rear
- Open the reservoir and use the syringe or turkey baster to remove most of the old fluid. Do not let the reservoir run dry, because that draws air into the system.
- Refill the reservoir with fresh fluid of the type marked on the cap, leaving room for the diaphragm and cap to be reinstalled later.
- Attach the clear tubing to the bleeder valve you are working on and route the other end into the catch bottle. Keep the tubing routed upward for a short section so air bubbles can be seen moving through it.
- For the front brake, squeeze and hold the lever. For the rear brake, press and hold the pedal. Keep steady pressure on the lever or pedal while you open the bleeder.
- Open the bleeder about a quarter turn and let fluid and air flow out through the tubing. Watch the reservoir level and stop before it gets low.
- Close the bleeder before you release the lever or pedal. Releasing first can pull air back into the caliper.
- Repeat the squeeze, hold, open, close, and release sequence until fresh, clean, bubble-free fluid comes through the tubing. Top off the reservoir throughout the job so it never runs low enough to draw air in.
- If your bike has two front calipers, bleed each one in turn. A common approach is to start with the caliper farthest from the master cylinder, but on many adventure bikes the two are close enough that either order works as long as you finish with a firm lever.
- Move to the rear brake and repeat the same process with the pedal. Keep the rear reservoir topped off and close the bleeder before releasing the pedal each time.
- When clean fluid is flowing with no bubbles, close the bleeder snugly without overtightening it. Overtightening can damage the bleeder or the caliper.
Finish, Test, and Check for Leaks
Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the bike. Check for leaks at the bleeder valves and at the banjo fittings where the brake lines attach. The lever and pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Before riding normally, test the brakes at low speed in a safe area and make sure the Africa Twin DCT stops smoothly and predictably.
Troubleshooting and When to Stop
If the lever or pedal will not firm up after several bleeding attempts, or if it firms up only after pumping, air is still in the system or fluid is bypassing internally. Persistent bubbles, fluid leaking from the master cylinder or caliper, or a lever that feels different every time you pull it are reasons to stop and diagnose the problem rather than keep riding. Because this 2017 Africa Twin DCT has ABS, any situation where the reservoir ran dry or the ABS unit or its lines were disconnected may leave air trapped where a standard caliper bleed cannot remove it. In that case, take the bike to a shop with the correct diagnostic equipment instead of trying to force a firm lever at home.
Related Shopping Categories
Shop Brake Fluid for a 2017 Honda Africa Twin DCT Motorcycle.
Shop Brake Lines for a 2017 Honda Africa Twin DCT Motorcycle.
Shop Brake Pads for a 2017 Honda Africa Twin DCT Motorcycle.
Shop Stands for a 2017 Honda Africa Twin DCT Motorcycle.
Shop Brake Tools for a 2017 Honda Africa Twin DCT Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.