Bleeding the Brakes on a 2016 Kawasaki Ninja 300 ABS
Shop parts for a 2016 Kawasaki EX300 - Ninja 300 ABS Motorcycle.What This Bike's Brake System Looks Like
The 2016 Ninja 300 ABS runs hydraulic disc brakes at both ends. A lever-mounted master cylinder on the handlebar feeds the front caliper, and a pedal-operated master cylinder down at the right footpeg feeds the rear caliper. Because this is the ABS version of the EX300, there is also an ABS modulator plumbed into the system between the master cylinders and the calipers. That single fact shapes the whole job: a routine bleed at the calipers is exactly what you want for refreshing fluid, but if air has been allowed into the modulator itself, the home mechanic generally cannot push it out with a lever and a bottle. There are no linked or combined brakes on this model, so the front lever works the front brake only and the pedal works the rear only. Each circuit is bled separately, and neither one affects the other.
Signs It's Time to Bleed
The most common tip-off is feel. A lever that has gone soft, or one that now travels noticeably closer to the grip than it used to, usually means air or moisture has worked its way into the circuit. The same goes for a rear pedal that feels vague or needs a long stroke before it bites. Pull the reservoir cap and look at the fluid — fresh brake fluid is clear and pale, while fluid that has been in service for a few seasons turns dark, cloudy, or tea-colored. Any job that opened the hydraulic system is an automatic trigger: new brake lines, a caliper rebuild, master cylinder service, or a line that was disconnected for any reason. Even with no symptoms at all, brake fluid absorbs moisture from the air over time, and that moisture lowers the fluid's boiling point. Under hard or repeated braking, fluid that boils creates vapor, the lever goes long, and you get brake fade at exactly the wrong moment. Many riders simply refresh the fluid on a regular interval as preventive maintenance rather than waiting for a problem to announce itself.
Tools and Supplies to Gather
Have everything laid out before you crack anything open, because once the reservoir is uncapped you do not want to be hunting for a rag.
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type and do not use a bottle that has been sitting open in the garage.
- A box-end wrench that fits the bleeder valve snugly. A box-end grips the flats far better than an open-end and is much less likely to round the bleeder.
- A length of clear tubing that fits tightly over the bleeder nipple, plus a catch bottle to route the old fluid into.
- Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir.
- The correct driver for the reservoir cap screws.
- Optional but genuinely helpful for a solo job: a one-way check-valve bleeder or a vacuum bleeder, either of which removes the need to coordinate the lever and the bleeder valve by yourself.
Setting Up Safely
Get the bike secure and upright on a stand before you touch a fastener. A bike that tips mid-bleed can spill fluid across paint and plastics, and brake fluid attacks both on contact. Turn the handlebars so the front reservoir sits level, then drape rags over the tank area, the fairing panels, the instrument cluster, and anything else below the reservoir that fluid could drip onto. Do the same around the rear reservoir and caliper. If a drop does land on a painted or plastic surface, wipe it up immediately and rinse the area with water rather than letting it sit.
Bleeding the Front Brake
- Remove the reservoir cap and diaphragm, then use the syringe or baster to draw most of the old fluid out of the reservoir. Leave enough in the bottom that you are not pulling air into the master cylinder port.
- Refill with fresh fluid from the sealed container.
- Push the clear tubing onto the front caliper bleeder and route the other end into the catch bottle, with the bottle positioned so you can watch the fluid coming through the tube.
- Squeeze the front lever and hold it against the grip.
- Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch for bubbles.
- Close the bleeder before you release the lever. Releasing with the bleeder open draws air straight back into the caliper.
- Release the lever slowly, then repeat the squeeze–hold–open–close–release cycle. Check the reservoir level every few cycles and top it off so it never runs low enough to pull air in.
- Keep going until the fluid coming through the tube is clean and free of bubbles, then close the bleeder.
If your bike is fitted with two front calipers, bleed them one at a time rather than trying to do both at once. As a general practice, start with the caliper farthest from the master cylinder in terms of hydraulic path, then move to the closer one.
Bleeding the Rear Brake
- Open the rear reservoir, remove most of the old fluid, and top it up with fresh fluid.
- Fit the clear tubing over the rear caliper bleeder and into the catch bottle.
- Press and hold the brake pedal.
- Open the bleeder a quarter turn, let fluid and air escape, then close it before releasing the pedal.
- Repeat, watching the tube for bubbles and keeping the reservoir topped off, until the fluid runs clean and clear.
Finishing and Checking for Leaks
Tighten the bleeder snugly with the box-end wrench. Snug is the goal — do not lean on it, because overtightening can damage the seat and create a leak where there wasn't one. Fill the reservoir to the level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder and the banjo fittings at both the caliper and the master cylinder for any weeping or wetness.
Test Before You Ride
The lever and pedal should feel firm and consistent, and should hold that firmness when you squeeze or press steadily for several seconds. A lever that slowly sinks toward the grip under constant pressure is not right. Spin each wheel by hand to confirm the brakes are not dragging. Then, in a safe open area at low speed, apply each brake individually and confirm it bites predictably before you ride normally.
When to Stop and Take It to a Shop
If the lever will not firm up after several honest bleeding attempts, if it only firms up when you pump it, or if bubbles keep appearing no matter how long you work, stop and reassess. Fluid weeping from the master cylinder or caliper, or a reservoir that ran dry at any point during the job, are both reasons to hand the bike to a professional. On an ABS machine like this one, air that has migrated into the modulator typically needs dealer-level equipment to purge properly, and no amount of lever pumping at the caliper will fix it. A shop visit is far cheaper than a brake failure.
Related Shopping Categories
Shop Brake Fluid for a 2016 Kawasaki EX300 - Ninja 300 ABS Motorcycle.
Shop Brake Lines for a 2016 Kawasaki EX300 - Ninja 300 ABS Motorcycle.
Shop Brake Pads for a 2016 Kawasaki EX300 - Ninja 300 ABS Motorcycle.
Shop Stands for a 2016 Kawasaki EX300 - Ninja 300 ABS Motorcycle.
Shop Brake Tools for a 2016 Kawasaki EX300 - Ninja 300 ABS Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.