Bleeding the Brakes on a 2015 Yamaha FJ-09
Shop parts for a 2015 Yamaha FJ-09 Motorcycle.The 2015 Yamaha FJ-09 is a sport tourer built around Yamaha’s punchy three-cylinder engine, and it stops with hydraulic disc brakes front and rear with ABS. The front brake is fed by the master cylinder and reservoir on the right handlebar. The rear brake is fed by a separate master cylinder operated by the foot pedal, with its own reservoir. Each circuit ends at a bleeder on its caliper and is bled independently. A routine bleed through those bleeders is the normal way to refresh fluid on this ABS-equipped bike.
Why Bleed the FJ-09?
Brake fluid absorbs moisture over time. That moisture lowers its boiling point, and hard braking, such as a spirited ride through the hills or a long descent with luggage, can heat old fluid until it boils. The vapor that forms compresses, so the lever goes soft and the brakes fade. Many riders refresh the fluid on a regular schedule even when the brakes feel fine.
Bleed sooner if:
- The lever feels spongy or pulls closer to the grip than it used to
- The rear pedal feels soft or sinks
- The fluid in a reservoir has turned dark or cloudy
- The system was opened for new lines, caliper service, or master cylinder repair
Tools and Supplies
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valves
- Clear tubing that fits snugly over the bleeder
- A catch bottle
- A syringe or turkey baster
- A screwdriver or driver for the reservoir caps
- Rags or shop towels
A one-way check-valve bleeder or vacuum bleeder lets you do the job without a helper.
Preparing the Bike
Support the bike securely upright on a paddock stand or other suitable stand. Turn the handlebars until the front reservoir is level. Cover the tank, bodywork, and instruments with rags. Most brake fluids damage paint and plastic on contact, so wipe up any spill immediately and rinse with water. Clean the reservoir caps before opening them.
Bleeding Steps
- Remove the front reservoir cap and diaphragm.
- Draw out most of the old fluid with the syringe, keeping the reservoir from running dry.
- Refill with fresh fluid.
- Attach the clear tube to the bleeder of the front caliper farthest from the master cylinder, with the free end in the catch bottle.
- Squeeze and hold the lever.
- Open the bleeder about a quarter turn to let fluid and air escape.
- Close the bleeder before releasing the lever.
- Repeat, topping off the reservoir every few strokes so it never runs low enough to draw in air.
- When fresh, clean, bubble-free fluid comes through, close the bleeder.
- Bleed the second front caliper, if your bike has one.
- Bleed the rear caliper using the foot pedal and rear reservoir.
Tips for a Clean Bleed
Use smooth, steady strokes rather than fast pumping. Watch the clear tube and keep going until the fluid runs clean and the bubbles stop. Keep the reservoir topped up constantly, because on an ABS bike, air drawn into the master cylinder can reach the ABS unit, where a caliper bleed may not clear it. Keep the fresh fluid capped, and never reuse fluid from the catch bottle.
Finishing and Testing
Tighten each bleeder snugly without overtightening. Fill the reservoirs to the correct level marks, reinstall the diaphragms and caps, and clean away any spilled fluid. Check the bleeders and banjo fittings for leaks, and dispose of the old fluid properly.
The lever and pedal should feel firm and consistent and should not slowly sink under steady pressure. Spin both wheels to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally.
When to See a Shop
Have the bike inspected if the lever will not firm up after several attempts, only firms up after pumping, keeps producing bubbles, or if fluid leaks from a master cylinder or caliper. If a reservoir ran dry or the ABS unit or its lines were disconnected, air may have entered the ABS unit, and the system may require a dealer-level procedure or diagnostic tool.
Related Shopping Categories
Shop Brake Fluid for a 2015 Yamaha FJ-09 Motorcycle.
Shop Brake Lines for a 2015 Yamaha FJ-09 Motorcycle.
Shop Brake Pads for a 2015 Yamaha FJ-09 Motorcycle.
Shop Stands for a 2015 Yamaha FJ-09 Motorcycle.
Shop Brake Tools for a 2015 Yamaha FJ-09 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.