Bleeding the Brakes on a 2009 Kawasaki Concours 14 (ZG1400)
Shop parts for a 2009 Kawasaki ZG1400 - Concours Motorcycle.
Know the System Before You Open It
The 2009 Kawasaki Concours 14, sold as the ZG1400, runs hydraulic disc brakes at both ends, and it is an ABS-equipped machine. That combination shapes everything below. Because both wheels are hydraulically actuated, you have two separate circuits to service: the front system fed by the lever-mounted master cylinder, and the rear system fed by the pedal master cylinder. They share nothing but the fluid specification, so each gets its own reservoir, its own bleeder, and its own bleeding session.
The ABS unit sits between the master cylinders and the calipers. For a routine fluid refresh—the kind you do because the fluid is dark or the lever feels soft—a normal bleed at the caliper bleeders is all that is required. The catch is air. If the reservoir ever ran dry, or if a line, caliper, or the ABS unit itself was disconnected, air can be trapped inside the ABS hardware where a hand bleed will not reach it. That situation calls for a dealer-level procedure, and it is covered again at the end of this article.
This bike is not a linked-brake model, so the front lever works the front brake only and the pedal works the rear only. That keeps the job straightforward: two independent circuits, bled one at a time.
Why and When to Bleed
Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. Moisture does two bad things. It lowers the fluid's boiling point, so hard, repeated braking can generate vapor in the lines and give you a lever that goes soft exactly when you need it most. It also darkens the fluid and can accelerate wear inside the system. Many riders simply refresh the fluid on a regular interval rather than waiting for a symptom.
Bleed when the lever or pedal feels spongy, when the lever travels closer to the grip than it used to, when the fluid in either reservoir looks dark or cloudy, or after any work that opened the hydraulic system—new lines, caliper service, or master cylinder work. If you have just replaced pads and pushed the pistons back, a quick bleed is also a reasonable precaution.
Tools and Supplies
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type.
- A box-end wrench that fits the bleeder valve snugly.
- Clear tubing sized to fit tightly over the bleeder nipple.
- A small catch bottle for the old fluid.
- Rags or shop towels, plus a syringe or turkey baster for pulling old fluid out of the reservoir.
- The correct driver for the reservoir cap screws.
- Optional but helpful: a one-way check-valve bleeder or a vacuum bleeder, which makes a one-person job much easier.
Setting Up Safely
Get the bike on a stand so it is stable and upright. For the front circuit, turn the handlebars until the reservoir on the lever perch sits level; a tilted reservoir will spill. Lay rags over the tank, the fairing panels, the instrument cluster, and anything else below the reservoir, because brake fluid attacks paint and plastic on contact. If a drop lands where it should not, wipe it up immediately and rinse the area with water.
Work in a ventilated space and keep the fluid container capped whenever you are not pouring from it. Old fluid in the catch bottle should be disposed of properly, not poured down a drain.
The Bleeding Procedure, Step by Step
- Wipe the reservoir cap and the area around it clean so no grit falls in. Remove the cap and the diaphragm.
- Use the syringe or baster to draw most of the old fluid out of the reservoir. Leave enough to cover the port at the bottom—never let the reservoir run dry, or you will pull air straight into the system.
- Top the reservoir up with fresh fluid from the sealed container.
- Push the clear tubing onto the bleeder nipple and route the other end into the catch bottle, with the bottle positioned so the tube's end stays submerged.
- Fit the box-end wrench onto the bleeder.
- Squeeze the front lever and hold it, or press and hold the rear pedal if you are working the rear circuit.
- Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch the reservoir level as you do this.
- Close the bleeder before you release the lever or pedal. Releasing with the bleeder open draws air back in through the nipple.
- Repeat the squeeze–hold–open–close–release cycle, topping off the reservoir every few cycles so it never drops low. Continue until the fluid coming through the tube is clean and free of bubbles.
- If your bike has two front calipers, bleed each one in turn, treating them as separate jobs. A common approach is to start with the caliper farthest from the master cylinder and work toward the closest, though on a twin-caliper front end either order will clear the system as long as you are thorough.
- When the fluid runs clean, hold pressure on the lever or pedal, close the bleeder snugly—firm, not overtightened—and release.
Finishing the Job
Fill the reservoir to the level marking on the body, not to the brim. Reinstall the diaphragm and cap and tighten the screws evenly. Wipe down the caliper, the bleeder, and the master cylinder, then check for weeping at the bleeder and at the banjo fittings. A damp bleeder after a few minutes of sitting means it needs another snug turn.
Testing and Troubleshooting
Before you ride, the lever and pedal should feel firm and consistent, and they should hold pressure without slowly sinking. Spin each wheel and confirm the brake is not dragging. Then test at low speed in a safe, empty area before riding normally.
If the lever firms up only after several pumps, or will not firm up at all after repeated bleeding, stop. Persistent bubbles, fluid weeping from the master cylinder or a caliper, or any suspicion that air entered the ABS unit means the bike should go to a shop with the equipment to cycle the ABS pump. That is not a failure on your part—it is simply the point where the job leaves the home garage.
Related Shopping Categories
Shop Brake Fluid for a 2009 Kawasaki ZG1400 - Concours Motorcycle.
Shop Brake Lines for a 2009 Kawasaki ZG1400 - Concours Motorcycle.
Shop Brake Pads for a 2009 Kawasaki ZG1400 - Concours Motorcycle.
Shop Stands for a 2009 Kawasaki ZG1400 - Concours Motorcycle.
Shop Brake Tools for a 2009 Kawasaki ZG1400 - Concours Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.