Bleeding the Brakes on a 1999 Kawasaki EX500 / Ninja 500

Shop parts for a 1999 Kawasaki EX500 - Ninja 500 Motorcycle.

What the 1999 EX500's Brake System Looks Like

The 1999 Kawasaki EX500 — sold as the Ninja 500 — stops on hydraulic disc brakes at both ends. A handlebar-mounted master cylinder feeds the front caliper, and a master cylinder at the pedal feeds the rear caliper. Each end has its own reservoir, its own sealed hydraulic circuit, and its own bleeder valve at the caliper, so a complete fluid refresh means bleeding both. There is no ABS unit and no linked-brake plumbing on this machine, which is genuinely good news for a home mechanic: the front lever and the rear pedal are completely independent, nothing has to be sequenced between them, and a plain pump-and-bleed at each caliper is the whole job. You can do the front first or the rear first, though most riders start up front because that is the brake they feel most often.

How to Tell the System Is Due for a Bleed

Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. That absorbed water lowers the fluid's boiling point, and under hard or repeated braking it can turn to vapor in the caliper — which feels exactly like air in the line and shows up as a lever that goes soft or a pedal that sinks. Even if the bike feels fine, dark, cloudy, or tea-colored fluid in either reservoir is a clear sign the fluid is old. A lever that pulls closer to the grip than it used to, a spongy feel at the lever or pedal, or a brake that only comes good after two or three pumps all point to air in the system. You also need to bleed after any work that opened the hydraulics: new lines, a caliper rebuild, a master cylinder service, or a fluid top-off that let the reservoir run dry.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container — once a bottle is opened it starts absorbing moisture, so use new stock
  • A box-end wrench that fits the bleeder valve snugly; a box-end grips better than an open-end and is less likely to round the hex
  • A length of clear tubing that fits tightly over the bleeder nipple, plus a small catch bottle
  • Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoirs
  • The correct driver for the reservoir cap screws — these are usually small Phillips heads and strip easily
  • Optional: a one-way check-valve bleeder or a vacuum bleeder, both of which make a solo job much less fiddly

Setting Up Before You Open Anything

Get the bike securely upright on a stand so it cannot tip while you are working at the bars or the rear caliper. Turn the handlebars until the front reservoir sits level, since a tilted reservoir will spill the moment the cap comes off. Brake fluid attacks paint, clearcoat, and many plastics on contact, so drape rags over the tank or bodywork, the instrument cluster, and the front fender before you loosen a single screw. If a drop does land on a painted surface, wipe it up immediately and rinse the area with water rather than rubbing it in. Work in a well-ventilated space and keep the fluid off your skin.

Bleeding the Front Brake

  1. Clean around the reservoir cap, then remove the cap screws, the cap, and the rubber diaphragm. Set them on a clean rag.
  2. Draw most of the old fluid out of the reservoir with the syringe or baster. Leave a little in the bottom so you do not push air into the master cylinder.
  3. Top the reservoir up with fresh fluid of the type marked on the cap.
  4. Slip the box-end wrench over the front bleeder valve, then push the clear tubing onto the nipple and route the other end into the catch bottle. A little fluid in the bottle stops air from being drawn back up the tube.
  5. Squeeze the front lever slowly and hold it against the grip.
  6. Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch the tube, not your hands.
  7. Close the bleeder before you release the lever. Releasing with the bleeder open pulls air straight back into the caliper.
  8. Release the lever slowly and let it return. Check the reservoir level and top it off — it drops fast, and letting it run dry means starting over.
  9. Repeat the squeeze, open, close, release cycle until the fluid coming through the tube is clean and free of bubbles.
  10. Finish with the lever held, the bleeder closed snugly, and the reservoir filled to the level marking. If your bike has more than one caliper on a circuit, bleed the caliper farthest from the master cylinder first, then the closer one.

Bleeding the Rear Brake

The rear circuit works the same way, just with the pedal instead of the lever. The rear reservoir is small, so check and top it far more often than you think you need to. Remove the cap and diaphragm, pull the old fluid out, refill with fresh, fit the wrench and tubing on the rear bleeder, then press and hold the pedal, crack the bleeder a quarter turn, close it, and release. Keep cycling until the fluid runs clean and bubble-free, then top the reservoir to its mark and refit the diaphragm and cap.

Finishing Up and Testing Before You Ride

Wipe down both calipers and reservoirs, and check for weeping at the bleeder valves and at the banjo fittings where the lines attach. The lever and pedal should feel firm and consistent, and should hold pressure without slowly sinking while you hold them. Spin each wheel by hand to confirm the brakes are not dragging. Then, in a safe open area, test at walking pace and again at low speed before riding normally. If a lever refuses to firm up after several rounds, if it only firms up when you pump it, if bubbles keep appearing, or if you see fluid at the master cylinder or caliper, stop and have the bike inspected — a brake system that will not hold pressure is not something to ride on.

Related Shopping Categories

Shop Brake Fluid for a 1999 Kawasaki EX500 - Ninja 500 Motorcycle.

Shop Brake Lines for a 1999 Kawasaki EX500 - Ninja 500 Motorcycle.

Shop Brake Pads for a 1999 Kawasaki EX500 - Ninja 500 Motorcycle.

Shop Stands for a 1999 Kawasaki EX500 - Ninja 500 Motorcycle.

Shop Brake Tools for a 1999 Kawasaki EX500 - Ninja 500 Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.