Bleeding the Brakes on a 1997 Kawasaki ZG1000 Concours
Shop parts for a 1997 Kawasaki ZG1000 - Concours Motorcycle.The 1997 Kawasaki ZG1000 Concours uses hydraulic disc brakes at both ends, so both the front lever and the rear pedal act on fluid-filled calipers. This model is not an ABS or linked-brake machine, which keeps the job straightforward: you bleed the front system at the front caliper and the rear system at the rear caliper, one at a time. The goal is to replace old fluid and remove trapped air so the lever and pedal feel firm and consistent.
What This Concours Brake System Uses
Because the Concours has hydraulic discs front and rear, there is no mechanical rear drum brake to adjust instead of bleed. Both brakes use fluid from their own master cylinder reservoirs, and both can draw air if the fluid level runs low or if the system has been opened for hose, caliper, or master-cylinder work. If your bike has two front calipers, treat each front caliper as a separate bleed point and service them one at a time. Do not assume a particular number of bleeders or a particular wrench size; fit the tool to the bleeder on your bike.
Why and When to Bleed the Brakes
Bleed the brakes when the front lever feels spongy, pulls closer to the grip than it used to, or slowly sinks under steady pressure. The same applies to a rear pedal that feels soft or travels farther than normal. Dark, cloudy, or contaminated fluid in the reservoir is another sign that fresh fluid is due. You should also bleed after any work that opened the hydraulic system, such as replacing a brake line, servicing a caliper, or repairing a master cylinder.
Even without symptoms, brake fluid absorbs moisture over time. That moisture lowers the fluid’s boiling point and can contribute to brake fade under hard or repeated use. Many riders refresh brake fluid on a regular schedule as preventive maintenance rather than waiting for a soft lever.
Tools and Supplies for a Clean, Controlled Bleed
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve snugly
- Clear tubing that fits tightly over the bleeder valve
- A clean catch bottle for used fluid
- Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir
- The correct driver for the reservoir cap screws
- Optional: a one-way check-valve bleeder or vacuum bleeder to make one-person bleeding easier
Setting Up the Bike and Protecting Surfaces
Support the Concours securely upright on a stand so it cannot tip while you are working the lever or pedal. Turn the handlebars so the front reservoir sits level before you open it. Cover painted bodywork, plastic panels, the instrument area, and any nearby surfaces with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water.
Work in a well-ventilated area and keep used fluid in the catch bottle so it does not contaminate the floor or nearby parts. Do not let the reservoir run dry at any point during the procedure; that is the most common way to pull air into the system and turn a simple bleed into a longer job.
Bleeding the Front and Rear Hydraulic Brakes
- Work on one brake system at a time. Start with the caliper farthest from its master cylinder if you are unsure where to begin, and complete that circuit before moving to the other.
- Remove the reservoir cap and diaphragm. Use the syringe or turkey baster to remove most of the old fluid from the reservoir without letting the level drop low enough to draw air into the master cylinder.
- Refill the reservoir with fresh fluid from the sealed container, leaving enough room for the diaphragm and cap to be reinstalled later.
- Push the clear tubing onto the bleeder valve and route the other end into the catch bottle. Keep the bottle lower than the bleeder so fluid and air can flow away.
- Squeeze and hold the front lever, or press and hold the rear pedal, to build pressure in the system.
- Open the bleeder about a quarter turn with the box-end wrench. Fluid and any trapped air will move through the tubing into the catch bottle.
- Close the bleeder before releasing the lever or pedal. Releasing first can draw air back into the caliper.
- Release the lever or pedal, then repeat the squeeze-hold-open-close sequence. Check the reservoir level often and top it off with fresh fluid so it never runs low.
- Continue until the fluid coming through the tubing is clean, fresh-looking, and free of bubbles. If your Concours has two front calipers, repeat the process on the other front caliper after finishing the first.
- Move to the rear brake and repeat the same sequence using the rear pedal and rear caliper bleeder. Keep the rear reservoir topped off throughout.
- When the fluid runs clear and bubble-free, close the bleeder snugly without overtightening it. Over-tightening can damage the bleeder or its seat.
- Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe away any spilled fluid.
Final Checks and a Low-Speed Test
Check the bleeder valves and the banjo fittings at the master cylinder and caliper for leaks. The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Before riding normally, test the brakes at low speed in a safe area and make sure both ends slow the bike smoothly and predictably.
When the Job Should Go to a Shop
If the lever or pedal will not firm up after several careful bleeding attempts, stop and have the system inspected. A lever that firms only after pumping, persistent air bubbles, or fluid leaking from the master cylinder or caliper also points to a problem that needs professional attention. Because this Concours has neither ABS nor linked brakes, you do not have an ABS unit or a linked-brake sequence to complicate the bleed, but any hydraulic brake that will not hold a firm feel should be treated as a safety issue rather than ridden until it improves.
Related Shopping Categories
Shop Brake Fluid for a 1997 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Lines for a 1997 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Pads for a 1997 Kawasaki ZG1000 - Concours Motorcycle.
Shop Stands for a 1997 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Tools for a 1997 Kawasaki ZG1000 - Concours Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.