2011 Husaberg FE570 Torque Specs: Final-Year Large-Bore Enduro Reference
Shop parts for a 2011 Husaberg FE570 Dirt Bike.
The 2011 Husaberg FE570 is the final model year for this large-bore enduro machine, closing out the 565cc single-cylinder FE series before Husaberg transitioned to updated displacement classes. The 2011 FE570 carries the fully mature platform specification, with all fastener torque values consistent with the 2009–2010 models. Proper maintenance on this final-year example keeps it competitive and reliable for years of continued use.
Engine Torque Specifications
A 2011 FE570 approaching the end of its model run may carry significant competition mileage. Head bolt condition should be carefully checked at any top-end service—stretched or corroded bolts must be replaced before reassembly, as torquing compromised hardware to the correct reading does not restore adequate clamping force.
| Fastener | Torque (ft-lb) | Torque (Nm) |
|---|---|---|
| Spark plug | 15–18 | 20–25 |
| Oil drain bolt | 18–22 | 24–30 |
| Cylinder head bolts (8mm) | 18–22 | 24–30 |
| Cylinder head bolts (10mm) | 36–40 | 49–54 |
| Cylinder base nuts | 22–26 | 30–35 |
| Flywheel nut | 54–61 | 73–83 |
| Clutch hub nut | 54–61 | 73–83 |
Chassis & Suspension Hardware
Suspension and chassis torque values for the 2011 FE570 are unchanged from the 2009 and 2010 models. On a machine this age in active use, swingarm and linkage pivot bearings should be inspected and replaced if contaminated or worn before relying on retorquing alone to restore correct suspension action.
| Fastener | Torque (ft-lb) | Torque (Nm) |
|---|---|---|
| Fork clamp bolts — upper triple clamp | 11–15 | 15–20 |
| Fork clamp bolts — lower triple clamp | 15–19 | 20–26 |
| Handlebar clamp bolts | 18–22 | 24–30 |
| Swingarm pivot bolt | 54–61 | 73–83 |
| Rear shock upper mount | 29–36 | 39–49 |
| Rear shock lower mount | 29–36 | 39–49 |
| Shock linkage bolts | 29–36 | 39–49 |
Wheels, Brakes & Drivetrain
The 2011 FE570's wheel and brake hardware specifications are consistent with prior years. Thread locker on disc bolts and sprocket fasteners, a 1/2-inch drive wrench for flywheel and rear axle, and anti-seize on the spark plug cover the key thread prep requirements for any FE570 service.
| Fastener | Torque (ft-lb) | Torque (Nm) |
|---|---|---|
| Front axle nut | 36–43 | 49–58 |
| Rear axle nut | 54–61 | 73–83 |
| Rear sprocket bolts | 22–29 | 30–39 |
| Chain adjuster lock nuts | 18–22 | 24–30 |
| Front caliper mounting bolts | 18–22 | 24–30 |
| Front brake disc bolts | 14–17 | 19–23 |
| Rear caliper mounting bolts | 18–22 | 24–30 |
| Rear brake disc bolts | 14–17 | 19–23 |
Related Shopping Categories
Shop Torque Wrenches for a 2011 Husaberg FE570 Dirt Bike.
Shop Wrenches and Sockets for a 2011 Husaberg FE570 Dirt Bike.
Shop Thread Locker for a 2011 Husaberg FE570 Dirt Bike.
Shop Additional Tools for a 2011 Husaberg FE570 Dirt Bike.
Shop Penetrating Oil for a 2011 Husaberg FE570 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.
