Nice kit comes with good selection of bolts for the different heights and works excellent for the purpose. The plates have locking groves and hold together like they're welded together. The only reason for 4 stars is they are smaller then the factory kx250f mounts buy just enough to be kinda ulgy.
- 3 reviews
- 2 reviews
- 0 reviews
- 0 reviews
- 0 reviews
I wanted to raise the bars on my 2017 Yamaha FZ-10 I ordered a pair of risers from ROX risers but found I would need longer throttle and brake cables too.
After looking for an alternative, I came across the BikeMaster Aluminum risers. While their web page claims they would fit my FZ, alas, they do not.
I will say they make perfect sense and are really well made but they WILL NOT work for my bike. The crown bolts on the FZ screw into an off-angle clamp and the BikeMaster's are straight.
Looks like longer cables it is.
nice quality, easy install with multiple spacers to get the perfect height.
My son is more comfortable.
Very nice, looks good and brought my bars up to where I need them without having to get bigger bars on my kfx450r. Stock was just to short!
- Answered: 7
- Not Yet: 1
Question asked by Doyle
Question:Q: Will these fit my sportster 48 2011 stock barsQuestion asked 2 months 20 days ago
Question answered by PaulUser's contributor status: Top 1Question answered 2 months 20 days agoAnswer: A: The BikeMaster Aluminum Handlebar Risers are available in 7/8" and 1 1/8" diameters. These will not fit your 1" handlebar.
The 2011 H-D XL1200X Sportster-48 comes stock with a 1" diameter handlebar and has its lower handlebar cradles built as one piece with the top triple clamp. The lower cradles can not be lifted.
Our Rox Speed FX Street Riser will do what you need, shown in this link:
The Rox Speed FX Street Risers are to be installed in your original 1" clamps. The Rox Speed FX Street Riser provides you with new clamps to mount your 1" diameter handlebar, either 2" or 3" higher than before.
Question asked by JMWEBB
Question:Q: I have a 2017 Yamaha FZ-10 1 1/8 handlebar. I would like to order a set of your risers but a review from 2 years ago indicated they would not fit the FZ-10 due to the off angle of the clamp. Can you tell me if your risers will fit the FZ-10?Question asked 1 year ago
Question answered by PaulUser's contributor status: Top 1Question answered 1 year agoAnswer: A: The BikeMaster Aluminum Handlebar Risers mount directly on to your stock handlebar clamps, and will hold your handlebars in the same location. These fit your 2017 Yamaha FZ10.
Question asked by isaac
Question:Q: Will they work on a 04 honda crf150fQuestion asked 1 year 8 months ago
Question answered by Tyler GearheadUser's contributor status: Top 25Question answered 1 year 8 months agoAnswer: A: These are a universal product designed for street bikes so I cannot guarantee Fitment. I have included a link for risers designed for dirt bikes.
Question asked by Bull2152
Question:Q: Risers.Question asked 2 years 10 months agoWhich risers would be best for raising a 09 zx6r handlebars up an in or two?
Question answered by IsaacUser's contributor status: Top 10Question answered 2 years 10 months agoAnswer: A: It would not work with the stock clip on bars that come on your model.
Question asked by James
Question:Q: As long as the bars ar 7/8 will they work on motocross bikeQuestion asked 2 years 11 months ago
Question asked by metroknow
Question:Q: How do these fit - on top of the stock risers?Question asked Over 4 years agoI have an 82 Yamaha XS400 Maxim, and am looking to raise the bars a bit (the drag bars that were installed previously now make the controls hit the tank). I'm trying to understand how these risers will work with my existing setup - is the idea that you add these to the top of your existing riser, and the provided bolts will thread into the stock riser base, if that makes sense? Attaching a photo. To install would I: 1. Remove the top of the riser and the hex bolts, leaving the base in place 2. Lift the bar out 3. Add on these spacers, finishing with the bottom holder spacer 4. Put the bar back 5. Put the top holder on and thread in with the longer hex bolt Thanks!
Question answered by MotoSportExpertUser's contributor status: MotoSport Staff ExpertQuestion answered Over 4 years agoAnswer: A: Yes the BikeMaster Aluminum Handlebar Risers would bolt onto the existing mount. Feel free to give us a call at 888-676-8853 and we would be happy to help you out with your order.
Question asked by gasgas
Question:Q: Different segments heightQuestion asked Over 5 years agoFrom the pictures, I believe that there are 3 different types of height, are their height into 20mm, 25mm, and 30mm? Will the different segments of the riser compensate the holding strength of the handle bar? I'm using stock handle bar, 7/8" Thanks
Question answered by MotoSportExpertUser's contributor status: MotoSport Staff ExpertQuestion answered Over 5 years agoAnswer: A: The first riser is 1" and the 3 after that raise it an additional 3/16ths each.
Question asked by sjay09
Question:Q: Will these fit my motorcycle?Question asked Over 5 years agoI am riding a Yamaha XJ6 Diversion 10. It has a stock handlebar fitted to it. Which of the sizes will fit it?
Question answered by MotoSportExpertUser's contributor status: Expert MotoSport StaffQuestion answered Over 5 years agoAnswer: A: As long as you still have the stock 7/8" bars you will want to go with the 7/8" risers.