Rebuilt the swing arm and rear suspension. Perfect kit. Al bearings seals and clips needed for the job great quality.. can’t wait to ride. Titened up the rear end very nice. On a old 2000 Cr125r like a new bike now
Write your review and you'll automatically be entered in our monthly drawing. Include an image or video to DOUBLE your chances to win!Write Your Review
Pivot Works bearings are the best in my opinion. They install with ease and have a lifetime guarantee, What else could you ask for?
I installed this kit on an 01' CR 250 with ease. Just freeze the bearings over night and torch them in you will have your bike back together in a matter of about an hour or so. There are plenty of good videos online that can show you how to torch them in. you will need a bench vise, some sockets, a pair of leather gloves and a propane torch.
Do not waste your money on bearing presses the old fashion way works great and gives you more money to spend on your bike.
Bought the kit...shock, linkage, and swingarm..unfortunately the swingarm bearings were incorrect. Everything else was fine
Glad to have a kit that has everything you need to repair you rear suspension. Didn't realize how much of a difference it made in my son's kx 85. Great kit for the money! Diffently would by again!
Had to replace every bearing on my sons yz250 and this kit had everything I needed. Once in bike was like new again
Pivot works is right there everythime with the bearing sets and cost to do a complete bike. Never doubt them and buy them, they are solid and hold up to all conditions.
OVERALL: Great product. I read a lot about Pivot Works not meeting oem spec bearings. No way.... I used my caliper and measured them. Unless my bike had aftermarket bearings installed by the previous owner, THERE THE SAME!
INSTALL: I used my craftsman sockets to pound/press out. If your bike is old like mine, invest in a propane torch or acetlyne. Getting the old bearings out is the tough part. Install is easy. Just make sure you grease the bearings before pressing them in. TIPS: -Have the manual on hand as each part isn't labeled. -Clean the recess in which the bearing will go into, and you almost don't need to use heat when pressing in the new bearings. -Install the bearing with the numbers/letters facing out. Your socket/press should be against the lettering/numbering.
RIDING: I'm no pro at motocross, but they made a HUGE difference. My old bearings were neglected by the previous owner and frozen. Rear suspension is so smooth now. I had no idea it'd make that big of a difference. Don't FORGET, you have a warranty so SAVE the packaging. Your basically buying 2 sets of bearings for a lower price then that of a single set of oem bearings! Deffinitly worth it!
Bearing aren't an exciting upgrade but a necessary one. I usually pull off my linkage and grease it every six months or so. (I average riding 5 hours a week .) But, this time when I pulled off my linkage the bearings were in pretty bad shape. I had never replaced the bearings before and I figured if the linkage bearings were shot the swingarm bearings were also. I was right. So, I ordered up this kit and it contained all the pieces I needed. I had access to a hydraulic press and that made the job quite easy. Just take your time when you are pushing out the old bearings. And, I recommend putting the new bearings in the freezer for about 15 minutes before you try to install them. It makes the job much easier.
No contest, these are the best bearings on the market.
finally a complete rear end kit that comes with shock upper and lowers cant go wrong with pivot works
I decided to tear apart my suspension soon after I purchased my 2003 YZ250 to re-grease the suspension. Later investigation revealed the suspension bearings were all dry, dirty grease with broken needle bearings, etc... Pivot works bearings hooked me right up. The bearings were installed using a press and numerous sockets, and a few jigs. time consuming but was happy with the end results, Suspension feels great!
Great buy for me, everything that I needed was in this kit combo. They were easy to install, and I did them myself. I had no problems what so ever. They are a really great buy, be better if they were about $10-$15 cheaper. Will recommend to all my friends. And I almost forgot shipping was really fast. Keep up the good work Motosport and Pivot Works.
Pivot works sends everything you need to get the job done. You need to go to the website to get instructions to do the installation.
This is truly a complete set of bearings.. I think they perform a little better than OEM ones too because they seem Like they will last longer. They are packaged very nice so nothing's is lost or broken. They are not very simple to install but that's not the manufacturers fault
because bearings can be difficult sometimes. But they are well worth it!! Not much else I can say about them other than I really like them!
Sweet fit nice and is correct for my bike awsome parts
This kit is exactly lie the original bearings, easy install just like OEM.
I priced out a couple of the bearings and bushings from Suzuki. I was able to get the ENTIRE set of bearings, bushings, and seals from Pivot Works for less than the cost of a couple of the OEM parts.
This is a bargain! Very complete kit.
No problems. Works great
Work good fit good not much to say about bearings.
Pivot Wrks always has good products, now you can click on one button and get all the bearings you need to rebuild your rear end.
If your asking for the Linkage itself, you need to go search oem parts. It says linkage and shock, but thats because your LOWER shock is hooked up to the linkage, so you get lower shock parts too.