Fuel Line Replacement on the 1997 Yamaha RT100
Shop parts for a 1997 Yamaha RT100 Dirt Bike.
If you have owned your 1997 Yamaha RT100 more than a few seasons, the fuel line deserves a hard look. It is a wear item almost nobody thinks about until it fails, and the failure is rarely graceful. Replacing the hose costs a few dollars, and doing it early beats doing it trailside with a leaking tank.
Why This Part Wears Out at All
Two things degrade a fuel line: time, and what sits inside it. Rubber loses flexibility as it ages, and a hose that spent eight years on a 1997 Yamaha RT100 has been hardening the whole time, ridden or parked. Hardened rubber cannot absorb vibration, so it cracks where it stretches over a fitting. Ethanol-blended gasoline is the other half — fuel sitting unused for months attracts moisture and breaks down, which is rough on hose material and leaves varnish behind. Add a dry climate baking out what flexibility remains, and a line that looked fine last season can be brittle by spring.
The Carbureted Setup on This RT100
The 1997 Yamaha RT100 runs a carbureted fuel system, which works in your favor. Fuel leaves the tank through a petcock — the small valve underneath — travels down a short rubber hose, and enters the carburetor at the float bowl inlet. You can shut fuel off at the source, and the line is a simple two-clamp affair with no pump pressure behind it.
Red Flags During a Pre-Ride Look
Most failing fuel lines warn you before letting go. The warnings are easy to dismiss, so it helps to know what you are looking at when you walk up to your 1997 Yamaha RT100.
- A puddle or damp patch underneath. Even a slow weep leaves evidence, usually below the tank or carburetor.
- A strong fuel smell in the garage. Odor lingering a day after parking is not normal.
- Visible cracking. Bend the hose gently; fine cracks that open under flex mean the rubber is done.
- A hose that feels hard or glazed. Healthy line is soft and slightly tacky.
- Bogging or running lean. A collapsed or deteriorated line restricts flow, and the engine acts like the tank is nearly empty.
Tools & Preparation
Nothing here is exotic, but having it within reach before you open the fuel system keeps the job from turning messy.
- Replacement fuel line in the correct inside diameter and length for your 1997 Yamaha RT100. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
One genuine safety note: gasoline vapor is heavier than air and travels along the floor toward anything that can ignite it. Work outdoors or with the door open, shut off any heater with a pilot light, keep the fuel container capped, and let a hot engine cool first.
Removing the Old Fuel Line
Close the petcock. Everything downstream of that valve is the only fuel you need to deal with, which on a 1997 Yamaha RT100 amounts to a few ounces in the line and float bowl.
Get that remaining fuel into a container rather than onto the floor. The float bowl drain screw is purpose-built for this — slip a hose over the nipple, aim it into your catch can, and crack the screw open. If you would rather drain the whole tank, do it now with the hose routed into the container.
Then release both clamps and work the hose off the fittings. Pliers handle spring clamps; a flat screwdriver handles screw clamps. Slide each clamp well back so it cannot fight you. To separate a stubborn hose from a barb, rotate it a quarter turn to shear the bond before pulling. If the rubber has gone hard enough that it will not release, split it with a knife along its length — the hose is being replaced anyway, and the fittings are what matter.
Routing and Securing the New Line
Trim the replacement to the same length as the original. Guessing causes problems at both ends of the range — excess hose finds something hot to lean against, and a short hose loads the fittings every time the engine moves. Cut cleanly and squarely.
Fit the tank-side end first, sliding the hose past the full barb until it bottoms out. If the line is stiff from sitting on a shelf, dip the end in hot water. Do not lubricate: no grease, no oil, no assembly lube on a fuel fitting. Beyond weakening the seal, it introduces contamination into the fuel your RT100 is about to run.
Connect the carburetor end and look at the whole run before securing anything. The hose should mirror the factory routing with clearance from the exhaust and no kinks. Then set both clamps directly over the barbed sections and tighten just enough to compress the rubber. Over-torquing a screw clamp scores the hose and creates a leak path over time.
Verifying the Repair
Open the fuel valve and let gravity do the testing. Give the RT100 a few minutes standing over clean cardboard, then inspect the tank-side and carburetor-side joints carefully. Wipe each dry first so new moisture is unmistakable.
Follow that with a running check. Start the engine, bring it to temperature, and look at both fittings again at idle — some leaks only appear once heat and vibration are in the system. A joint weeping under those conditions has a seating problem, not a clamp problem; pull it apart and push the hose fully home.
Then clean up and stay attentive for a ride or two. Dispose of old fuel properly, watch the clamps as the new rubber settles, and consider replacing an inline filter while the system is open. Anyone wanting more detail on what shortens fuel line life long term will find it in our complete overview of dirt bike fuel line service.
Related Shopping Categories
Shop Fuel Lines for a 1997 Yamaha RT100 Dirt Bike.
Shop Fuel Line Clamps for a 1997 Yamaha RT100 Dirt Bike.
Shop Petcocks for a 1997 Yamaha RT100 Dirt Bike.
Shop Fuel Filters for a 1997 Yamaha RT100 Dirt Bike.
Shop Fuel Stabilizer for a 1997 Yamaha RT100 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.