A Practical Fuel Line Walkthrough for the 1987 Suzuki RM250
Shop parts for a 1987 Suzuki RM250 Dirt Bike.
If you have owned your 1987 Suzuki RM250 more than a few seasons, the fuel line deserves a hard look. It is a wear item almost nobody thinks about until it fails, and the failure is rarely graceful. Replacing the hose costs a few dollars, and doing it early beats doing it trailside with a leaking tank.
Warning Signs Your RM250 Needs a New Line
Most failing fuel lines warn you before letting go. The warnings are easy to dismiss, so it helps to know what you are looking at when you walk up to your 1987 Suzuki RM250.
- A puddle or damp patch underneath. Even a slow weep leaves evidence, usually below the tank or carburetor.
- A strong fuel smell in the garage. Odor lingering a day after parking is not normal.
- Visible cracking. Bend the hose gently; fine cracks that open under flex mean the rubber is done.
- A hose that feels hard or glazed. Healthy line is soft and slightly tacky.
- Bogging or running lean. A collapsed or deteriorated line restricts flow, and the engine acts like the tank is nearly empty.
Why Fuel Lines Harden, Crack, and Fail
Rubber fuel line fails for reasons that have little to do with how hard you ride. Age drives it: the plasticizers keeping the hose flexible slowly migrate out, and pliable rubber turns stiff and glassy, so a small flex — bolting the tank down, rocking the bike onto a stand — opens a hairline crack. Dry, hot storage accelerates that, pulling volatiles out faster than a temperate garage would. Ethanol-blended pump fuel left sitting in the hose adds a second mechanism, attacking the inner wall and leaving gum that can flake into the fuel path on a 1987 Suzuki RM250.
Know the RM250 Fuel Layout First
Fuel delivery on the 1987 Suzuki RM250 is carbureted, so the plumbing is about as simple as it gets on a two-stroke dirt bike — tank, petcock, hose, carburetor. That petcock is the most useful thing about this job. Turn it off and the fuel stops, which means no siphoning and no fighting gravity while you work.
Gathering Parts and Setting Up
This is a low-cost job, and most of the preparation is about containing fuel rather than turning wrenches.
- Replacement fuel line in the correct inside diameter and length for your 1987 Suzuki RM250. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
Before the first fitting comes loose, handle the safety side. Gasoline vapor pools low and finds ignition sources you would never consider, including pilot lights across the room. Ventilate properly, keep fuel in a closed container, wear eye protection, and never open the system on a hot engine.
Taking the Failed Hose Off
Shut the petcock off first. That single step keeps this job clean on a carbureted RM250 — with the valve closed, the tank stays full and the only fuel to manage is what is already past the valve.
Empty the carburetor next. Attach a length of clear hose to the float bowl drain nipple, direct it into your container, and open the drain screw. A minute later the bowl is dry and you can work without fuel running down your arm.
With the fuel handled, address the clamps at each end. Squeeze spring clamp tabs together with pliers and walk the clamp down the hose, or loosen a screw clamp with a driver. The hose is usually the hard part: years of heat cycling effectively glue it to the barb. Twist first to break the bond, then pull straight off. When a line is badly hardened, cutting it off with a razor blade is safer for the fitting than prying at it.
Installing the Replacement Hose
Trim the replacement to the same length as the original. Guessing causes problems at both ends of the range — excess hose finds something hot to lean against, and a short hose loads the fittings every time the engine moves. Cut cleanly and squarely.
Fit the tank-side end first, sliding the hose past the full barb until it bottoms out. If the line is stiff from sitting on a shelf, dip the end in hot water. Do not lubricate: no grease, no oil, no assembly lube on a fuel fitting. Beyond weakening the seal, it introduces contamination into the fuel your RM250 is about to run.
Connect the carburetor end and look at the whole run before securing anything. The hose should mirror the factory routing with clearance from the exhaust and no kinks. Then set both clamps directly over the barbed sections and tighten just enough to compress the rubber. Over-torquing a screw clamp scores the hose and creates a leak path over time.
Confirming It Is Sealed
With the new line in place, open the petcock and stop. Let the 1987 Suzuki RM250 sit five minutes over a clean surface and use that time to examine both joints under a flashlight. A properly seated hose stays completely dry; anything else needs attention before the wheels turn.
The running test comes second. Fire the engine, let it warm, and look again — expansion and vibration find seals that hold fine cold and still. When you find a weep, resist the urge to overtighten. Disconnect, verify the hose is pushed fully over the barb, and reassemble; that is nearly always the actual problem.
Wrap up by disposing of the drained fuel appropriately and taking another look at the connections after your next ride. On carbureted bikes an inline filter, if fitted, is a serviceable part worth replacing at the same time. For deeper background on keeping fuel lines healthy between seasons, our full guide to dirt bike fuel line care is a useful companion read.
Related Shopping Categories
Shop Fuel Lines for a 1987 Suzuki RM250 Dirt Bike.
Shop Fuel Line Clamps for a 1987 Suzuki RM250 Dirt Bike.
Shop Petcocks for a 1987 Suzuki RM250 Dirt Bike.
Shop Fuel Filters for a 1987 Suzuki RM250 Dirt Bike.
Shop Fuel Stabilizer for a 1987 Suzuki RM250 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.