2018 Suzuki RMZ250 Dirt Bike Oil Change: Step-by-Step Guide
Shop parts for a 2018 Suzuki RMZ250 Dirt Bike.Why Oil Changes Matter on the 2018 RMZ250
The RMZ250 is a four-stroke 250-class motocross machine, and its engine oil does more than keep the crankshaft and camshafts moving. The same oil circulates through the transmission and clutch, so it carries metal particles, heat, and friction from every gear change and every hard launch. Over time that oil loses its ability to protect the parts it touches, and the clutch is usually the first thing to show it.
How you ride has a large effect on how quickly the oil wears out. A motocross bike ridden on a race-day schedule, with long full-throttle pulls and frequent clutch starts, will break its oil down much faster than a bike used for a casual weekend loop. Slow technical enduro riding can be just as hard on the oil. Crawling over roots and rocks in first and second gear keeps the clutch slipping a little and the engine running hot without much airflow, and heat is the single biggest enemy of motor oil. Easy trail riding at steady speeds is the gentlest use, but even that bike needs fresh oil on a regular basis.
Several signs tell you the oil is due. Oil that looks dark, almost black, or feels gritty between your fingers has picked up wear material and combustion byproducts. A clutch that drags, feels soft, or slips under acceleration often points to oil that no longer has the right friction characteristics. Shifting that turns notchy or harder to find neutral can also come from degraded oil. If it has been a long time since the last change, replace the oil whether or not any of these symptoms are present, because the oil ages even when the bike sits in the garage.
What You Will Need
- Motorcycle engine oil specified for your RMZ250, labeled for use with a wet clutch
- A new oil filter and new filter cover O-rings
- A new drain plug sealing washer
- A drain pan large enough to hold the full oil capacity with room to spare
- A funnel with a fine screen or a clean spout
- A socket or wrench that fits the drain plug and filter cover bolts
- Clean rags or shop towels
- Nitrile or mechanic’s gloves
- A torque wrench, if you have one
Use only motorcycle oil that is rated for a wet clutch. Automotive oils often contain friction modifiers designed for car transmissions and torque converters, and those additives can cause a motorcycle clutch to slip under load. Check the oil specified for your bike and buy that. Avoid any oil that does not state it is suitable for motorcycles with wet clutches.
Preparing the Bike Before You Drain
Start the engine and let it idle for a minute or two. Warm oil flows more freely and carries more suspended debris out with it. Shut the engine off and give it enough time to cool so the oil is warm but not hot enough to burn you. Hot oil can cause serious skin burns, so handle the drain pan and the drain plug with care.
Set the bike on a stand on firm, level ground. A level bike lets the oil drain completely, and it keeps the drain pan from tipping. If your bike has a skid plate or engine guard that blocks access to the drain plug or filter cover, remove it first.
Clean the area around the drain plug, the fill cap, and the filter cover before you open anything. Dirt and grit falling into the engine can damage bearings and the clutch. A stiff brush and a rag will remove most of what has collected in the bottom of the engine cases.
Draining and Refilling the Engine Oil
- Remove the fill cap so the oil can drain freely and air can enter the case.
- Position the drain pan beneath the drain plug on the bottom of the engine, then remove the drain plug and let the oil drain completely. Some models also have a second drain plug or an oil screen, so inspect the cases before you start and check for any additional drain points.
- Remove the oil filter cover and the filter. Before you pull the old filter out, note which way it faces so you can install the new one the same way.
- Clean the filter housing thoroughly with a rag, removing any metal particles or sludge that has settled in the chamber. If your bike has an oil screen, clean it at this point as well.
- Install the new oil filter in the same orientation as the old one, then fit new O-rings onto the filter cover and set the cover back in place.
- Inspect the drain plug. If it is magnetic, wipe off the fine metal particles stuck to it. Clean the threads and the sealing surface.
- Fit a new sealing washer onto the drain plug, then reinstall it snugly.
- Refill the engine through the fill opening with the specified amount of oil.
- Reinstall the fill cap.
Drain plugs and filter cover bolts thread into aluminum cases, and aluminum strips easily when it is overtightened. Tighten these fasteners carefully and evenly. If you have a torque wrench, set it to the specification for your bike. If you do not, snug each fastener until it seats and stop there.
Confirming the Correct Oil Level
The exact amount of oil varies from bike to bike, so use the specified amount for your RMZ250 as a starting point. The final level matters more than the total poured in, because some oil remains in the filter and passages after draining.
Check the level using the method your bike uses. Some bikes have a sight glass on the case, some use a dipstick on the fill cap, and some use a level check bolt. Learn which one applies to your bike before you begin. With a dipstick, some are read with the cap threaded in and others with the cap resting on the threads, so follow the method specified for your bike.
Because the filter and oil passages hold some oil, start the engine and let it idle briefly after the refill. Shut it off and wait a few minutes so the oil can settle back into the case, then recheck the level. Topping off after this rest period will give you a more accurate reading.
Both overfilling and underfilling cause problems. Too much oil can foam, increase crankcase pressure, and push oil past seals. Too little oil can starve the engine and clutch of lubrication. Aim for the level your bike calls for, and avoid guessing.
Final Checks and Cleanup
Start the engine and let it idle for a short time. Look closely at the drain plug, the fill cap, and the filter cover for any sign of seepage. If you see oil, shut the engine off and check that the fastener is snug and the washer or O-ring is seated correctly.
Reinstall any skid plate or guard you removed. Take used oil and the old filter to a recycling center or a shop that accepts them. Never pour used oil onto the ground or into household trash.
Finally, write down the date and your approximate riding time since the last change. Keeping a simple log makes it much easier to know when the next service is due, and it helps you spot patterns if the clutch or shifting starts to change.
Common Mistakes to Avoid
- Overtightening the drain plug or filter cover bolts, which can strip the aluminum threads
- Reusing the old sealing washer or filter O-rings
- Installing the oil filter backward
- Using automotive oil that can make the wet clutch slip
- Overfilling or underfilling the engine
- Forgetting to check for a second drain plug or an oil screen before draining
Related Shopping Categories
Shop Motor Oil for a 2018 Suzuki RMZ250 Dirt Bike.
Shop Oil Filters for a 2018 Suzuki RMZ250 Dirt Bike.
Shop Oil Drain Pans for a 2018 Suzuki RMZ250 Dirt Bike.
Shop Gaskets for a 2018 Suzuki RMZ250 Dirt Bike.
Shop Tools for a 2018 Suzuki RMZ250 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.