How to Change the Oil in a 2014 Beta 400 RS: The MotoSport Guide
Shop parts for a 2014 Beta 400 RS Dirt Bike!
The 2014 Beta 400 RS is a high-performance Italian four-stroke dual sport, renowned for its reliability and ease of maintenance. When it comes to changing the oil on this model, there are several unique features and steps to be aware of, as the bike uses separate oil compartments for the engine and the transmission. Following this proprietary MotoSport guide ensures a correct, mess-free service – and keeps your Beta running strong mile after mile.
Essential Supplies
- 800 ml of high-quality 10W-50 engine oil (such as BARDAHL XTC 10W-50, per Beta spec)
- Replacement oil filter (paper type)
- Drain pan
- 12 mm and 8 mm sockets
- Special seeger ring pliers (for oil filter change)
- Replacement crush washers/seals
- Shop towels and gloves
Before You Start
- Warm up the engine: Let the bike run until it reaches operating temperature. Warm oil flows and drains more efficiently, removing more contaminants.
- Park on level ground: Ensure the motorcycle is upright and secure for accurate draining and refilling.
- Safety first: Oil and engine parts get hot! Let the bike cool slightly to avoid burns.
Step-by-Step Oil Change Procedure
-
Remove Lower Skid Plate (if installed)
Loosen and remove the three mounting screws using the appropriate tool to expose the drain plugs. -
Drain the Engine Oil
Locate the engine oil drain bolt (front compartment). Place a drain pan under the bike and carefully remove the plug. Allow the oil to completely drain. For an extra thorough drain, gently lean the bike side-to-side to help evacuate lingering oil. -
Clean Components
Wipe the drain bolt and any wire netting filter clean, removing any shavings or debris. The drain plug may have a magnetic tip that collects metallic particles – thoroughly clean it off. -
Replace and Tighten Drain Bolt
Install a new crush washer/seal ring if needed and torque the drain bolt to 20 Nm as per Beta specification. -
Replace the Oil Filter
Locate and remove the oil filter cover by undoing its two screws (use an 8 mm socket). Using seeger ring pliers, pull the old paper oil filter out. Insert a new paper filter, reattach the cover, and tighten the screws to 6 Nm. -
Refill with New Oil
Remove the oil fill cap from the left side. Pour in 800 ml of fresh 10W-50 engine oil. Reinstall the fill cap. -
Check for Leaks and Oil Level
Start the engine and let it idle for five minutes. Check for any leaks. Switch the bike off, wait another five minutes, then use the sight glass to verify oil is at the correct level – it should appear in the middle of the sight window.
Special Notes for 2014 Beta 400 RS Owners
- The 2014 Beta 400 RS uses separate oil circuits and drain plugs for the engine and transmission. These are not interchangeable. Take care to use the correct type and quantity of oil in each – consult your owner's manual for transmission oil specifications.
- If your bike is a 2014.5 Race Edition, oil quantities and procedures may differ. Standard steps above apply specifically to non-race 2014 400 RS models.
- Always dispose of used oil responsibly in accordance with local environmental regulations.
- After an oil change, rides may feel smoother, and shifts can improve as old oil and debris are removed from the system.
The MotoSport Advantage
Keeps your Beta 400 RS running at peak performance with genuine parts and convenient oils and filter kits. For fast shipping and a full range of maintenance essentials, Shop parts for a 2014 Beta 400 RS Dirt Bike!
Related Shopping Categories
Shop Motor Oil for a 2014 Beta 400 RS Dirt Bike!
Shop Oil Filters for a 2014 Beta 400 RS Dirt Bike!
Shop Oil Drain Pans for a 2014 Beta 400 RS Dirt Bike!
Shop Tools for a 2014 Beta 400 RS Dirt Bike!
Shop Oil Fillers and Drain Plugs for a 2014 Beta 400 RS Dirt Bike!
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.