How to Change the Coolant in a 2009 Husaberg FE570
Shop parts for a 2009 Husaberg FE570 Dirt Bike.
Maintaining proper cooling is critical for your Husaberg FE570's reliability. Overheating risks engine damage – fresh coolant is a must for high performance riding. Follow this MotoSport.com proprietary guide for a safe and thorough coolant change.
What Makes the FE570 Unique?
- The FE570 features a distinctive engine orientation – the rear-tilted design improves mass centralization, but puts extra demand on optimal cooling.
- This model uses separate seals for the water pump shaft: one for coolant, one for engine oil, with a weep hole between them, intended to alert the owner to seal failure. If you notice any leakage from the weep hole, service your water pump seals and inspect for contamination immediately.
- The weep hole is positioned facing forward, making it vulnerable to dirt and debris. Owners often modify this for better protection.
- Check coolant levels regularly – the radiator should be filled to about 10 mm above the fins for safe operation.
Step-by-Step Guide to Changing the Coolant
- Cool Down: Always work on a cold engine to prevent burns. Place your bike upright on a stand.
- Remove Plastics as Needed: Remove spoilers or tank covers to access the radiator cap.
- Open the Radiator:
- Slowly loosen the radiator cap to release pressure.
- Remove cap once pressure is relieved.
- Locate Drain Points:
- The FE570 has a coolant drain bolt on the water pump housing. Place a drain pan underneath.
- Loosen the drain bolt, then remove it to let coolant flow out completely.
- Loosen lower radiator hose clamps for better drainage, if needed.
- Inspect Components:
- Examine the drained coolant for debris or oil – signs of water pump seal wear.
- Check gasket condition, replace if damaged.
- Flush If Needed
- If the coolant is contaminated, flush the system with distilled water before refilling.
- Reinstall Drain Bolt & Hose
- Fit a fresh sealing washer on the drain bolt, reinstall, and torque to spec.
- Refill Coolant
- Use a motorcycle-approved coolant, pre-mixed or mixed 50/50 with distilled water.
- Pour coolant in to about 10 mm above radiator fins.
- Burp the System
- Start the bike with the radiator cap off, run for a few minutes while gently revving and tilting the bike to release air pockets.
- Top off coolant if needed after air bubbles escape.
- Fill your overflow reservoir to the upper line.
- Reinstall Plastics & Cap
- Secure all panels and the radiator cap.
- Dispose Properly
- Take old coolant to a recycling center – never pour down drains.
Owner Tips for the FE570
- Periodically check both your water pump seals and the weep hole for leaks after coolant changes.
- Only use distilled water for mixing – tap water can cause mineral build-up and overheating.
- Consider a weep hole mod for better sealing against dirt. Consult MotoSport for the right parts.
- Always verify coolant level after every off-road ride, especially in hot climates or race conditions.
Your 2009 Husaberg FE570 is a high-performance machine with unique cooling system requirements. Regular coolant maintenance safeguards engine health so you can ride hard with confidence.
Related Shopping Categories
Shop Radiators for a 2009 Husaberg FE570 Dirt Bike.
Shop Coolant for a 2009 Husaberg FE570 Dirt Bike.
Shop Temperature Sensors for a 2009 Husaberg FE570 Dirt Bike.
Shop Tools for a 2009 Husaberg FE570 Dirt Bike.
Shop Radiator Hoses for a 2009 Husaberg FE570 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.
