Bleeding the Brakes on a 2022 Honda Africa Twin 1100 Adventure Sports ES

Shop parts for a 2022 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Start With the Layout of This Bike's Brake System

The 2022 Honda Africa Twin 1100 Adventure Sports ES runs hydraulic disc brakes at both the front and rear wheels, and ABS is part of the standard equipment package on this machine. That combination tells you two important things before you pick up a wrench. First, both circuits are sealed hydraulic systems fed by their own master cylinders, so both the front lever and the rear pedal can be bled and refreshed in a home garage with ordinary hand tools. Second, the presence of ABS means there is a limit to what a hand bleed can accomplish. Working fresh fluid through the caliper bleeders is exactly the right approach for routine maintenance, but if air has found its way into the ABS modulator itself — because a reservoir ran dry, or because the ABS unit or its lines were disconnected — the system may need a dealer-level procedure or diagnostic tool to purge properly. If your bike carries two front calipers, plan to bleed each one in turn rather than treating the front as a single circuit.

When a Bleed Is Actually Due

Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. That absorbed water lowers the fluid's boiling point, and a fluid that boils under hard, repeated braking creates vapor in the lines — which feels exactly like air and behaves exactly as badly. This is why many riders refresh the fluid on a schedule even when nothing feels wrong, particularly on a tall, heavy adventure bike that gets loaded down and ridden hard.

Beyond the calendar, bleed the brakes whenever the lever or pedal feels spongy or soft, when the lever pulls noticeably closer to the grip than it used to, when the fluid in the reservoir looks dark or cloudy, or after any work that opened the hydraulic system: new lines, caliper service, or master cylinder work. A lever that firms up only after several quick pumps is a classic sign that air is present.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container — opened fluid absorbs moisture, so do not reuse an old bottle
  • A box-end wrench that fits the bleeder valve snugly
  • A length of clear tubing that fits tightly over the bleeder nipple
  • A small catch bottle for the old fluid
  • Rags or shop towels, plus a syringe or turkey baster for pulling old fluid out of the reservoir
  • The correct driver for the reservoir cap screws
  • Optional but helpful: a one-way check-valve bleeder or a vacuum bleeder, which makes a one-person job much less fiddly

Setting Up Before You Open Anything

Get the bike secure and upright on a stand so the reservoirs sit level and the bike cannot tip while you are leaning on the lever. Turn the handlebars until the front reservoir is as close to horizontal as the bar position allows. Then cover the painted bodywork, the plastics around the bars, and the instrument area with rags. Brake fluid attacks paint and many plastics on contact, so a little prevention here saves a lot of grief. If a spill does happen, wipe it up immediately and rinse the area with water rather than letting it sit.

Bleeding the Front Brake

  1. Remove the reservoir cap and diaphragm, then use the syringe or baster to draw most of the old fluid out of the reservoir. Leave enough at the bottom that you are not pulling air into the master cylinder port.
  2. Top the reservoir up with fresh fluid from the sealed container.
  3. Push the clear tubing onto the front caliper bleeder and route the other end into the catch bottle, with the bottle positioned so the tubing runs upward away from the bleeder.
  4. Squeeze the front lever slowly and hold it against the grip.
  5. With the lever held, open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tubing.
  6. Close the bleeder before you release the lever. Releasing with the bleeder open draws air straight back into the caliper.
  7. Release the lever and repeat the squeeze-hold-open-close cycle. Check the reservoir level every few cycles and top it off — letting it run dry is the fastest way to turn a simple bleed into a long one.
  8. Keep going until the fluid coming through the tubing is clean and free of bubbles, and the lever feels firm rather than spongy.
  9. If your bike has two front calipers, repeat the whole process on the second caliper. As a general practice, start with the caliper farthest from the master cylinder and work toward the closest one.

Bleeding the Rear Brake

  1. Open the rear reservoir, remove most of the old fluid, and refill with fresh fluid.
  2. Fit the clear tubing over the rear caliper bleeder and into the catch bottle.
  3. Press and hold the brake pedal down.
  4. Open the bleeder a quarter turn, let fluid and air escape, then close it before releasing the pedal.
  5. Repeat, topping off the reservoir as you go, until the fluid runs clean and bubble-free and the pedal feels solid.

Finishing the Job Correctly

Once the fluid runs clean at both ends, tighten each bleeder snugly with the box-end wrench. Snug is the goal — do not lean on it, because overtightening can damage the seat and create a leak. Fill the reservoir to the level marking on the body, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder fittings and the banjo fittings at the calipers and master cylinder for any weeping or dampness.

Testing Before You Ride Normally

With the bike still supported, squeeze the front lever and press the rear pedal firmly. Both should feel firm and consistent, and neither should slowly sink while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Then ride slowly in a safe, open area and apply each brake gently at low speed before trusting them at road pace.

When to Stop and Take It to a Shop

If the lever will not firm up after several honest bleeding attempts, if it only firms up after pumping, if bubbles keep appearing no matter how long you work, or if you find fluid weeping from the master cylinder or a caliper, stop and have the bike inspected. The same applies if the reservoir has run dry or if any ABS component has been disturbed — air trapped in the ABS unit is not something a hand bleed will reliably clear on this bike, and it needs the proper equipment to sort out.

Related Shopping Categories

Shop Brake Fluid for a 2022 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Shop Brake Lines for a 2022 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Shop Brake Pads for a 2022 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Shop Stands for a 2022 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Shop Brake Tools for a 2022 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.