Bleeding the Brakes on Your 2021 Kawasaki Ninja 400
Shop parts for a 2021 Kawasaki EX400 - Ninja 400 Motorcycle.
Know Your Ninja 400's Brake Layout First
The 2021 Kawasaki EX400 — the Ninja 400 — stops on hydraulic disc brakes at both ends. A front caliper is fed by the master cylinder bolted to the handlebar, and a rear caliper is fed by a pedal-driven master cylinder tucked in behind the right-side bodywork. There is no linked or combined braking here, so the lever works the front brake only and the pedal works the rear only. That independence is good news for a home mechanic: each circuit stands alone, and you can service one without disturbing the other.
ABS is the one variable worth checking before you begin. Many 2021 Ninja 400s were sold with ABS, which adds a pump and valve block into the hydraulic path. If your bike has it, a routine flush through the caliper bleeders still works normally, provided the reservoir never runs dry. What you cannot do in a home garage is purge air that has migrated into the ABS unit itself. Keep that distinction in mind as you work, and read the troubleshooting section before you start if the lever has already gone completely soft.
Signs That It's Time to Bleed
A spongy lever or a rear pedal that feels vague and long are the classic symptoms of air in the system. So is a lever that now pulls noticeably closer to the grip than it used to, or one that firms up when you pump it and then slowly fades. Pop the reservoir cap and look at the fluid: dark, cloudy, or tea-colored fluid has done its time. Any job that opened the hydraulics — new lines, caliper service, master cylinder work — demands a bleed afterward.
Even with no symptoms at all, brake fluid absorbs moisture from the air over time, which lowers its boiling point and can bring on fade during hard or repeated braking. That is why many riders refresh the fluid on a regular interval rather than waiting for a problem to announce itself.
Tools and Supplies to Gather
- Fresh brake fluid of the type printed on your master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve snugly
- Clear tubing sized to fit tightly over the bleeder nipple
- A small catch bottle for the old fluid
- Rags or shop towels, plus a syringe or turkey baster for pulling old fluid out of the reservoir
- The correct driver for the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder makes the job far easier when you are working alone, since you are not trying to juggle a wrench, a lever, and a bottle at the same time.
Setting Up Without Making a Mess
Get the bike secure and upright on a stand so the reservoirs sit level. For the front, turn the handlebars until the reservoir on the bar is as flat as you can get it before you loosen the cap. Drape rags over the painted surfaces, the plastics, and the instrument area — brake fluid attacks paint and plastic on contact, and a single drip can leave a permanent mark. If a spill does happen, wipe it up immediately and rinse the area with water.
Bleeding the Front Brake
- Remove the reservoir cap and diaphragm, then use the syringe or baster to draw most of the old fluid out. Leave a little in the bottom so you do not push air into the line.
- Refill with fresh fluid from the sealed container and set the cap loosely back on to keep debris out.
- Slip the clear tubing over the front bleeder valve and route the other end into the catch bottle, with the bottle positioned so the tubing runs upward away from the bleeder.
- Fit the box-end wrench on the bleeder, then squeeze the front lever and hold it firm.
- Open the bleeder about a quarter turn. Fluid and air will push out through the tubing. Watch the reservoir level as you do this.
- Close the bleeder fully before you release the lever. Releasing with the bleeder open pulls air straight back into the caliper.
- Repeat the squeeze–hold–open–close–release cycle, topping the reservoir off between rounds so it never drops low enough to draw air in.
- Keep going until the fluid coming through the tubing is clean and free of bubbles, then close the bleeder and top the reservoir to the level marking.
If your bike happens to carry two front calipers, bleed them one at a time, starting with the caliper farthest from the master cylinder and finishing with the closer one.
Bleeding the Rear Brake
- Open the rear reservoir, remove the old fluid, and refill with fresh fluid.
- Attach the tubing to the rear bleeder and run it into the catch bottle.
- Press and hold the brake pedal, open the bleeder a quarter turn, then close it before releasing the pedal.
- Repeat until the fluid runs clean and bubble-free, checking the reservoir level constantly.
Finishing the Job
Tighten the bleeder snugly with the box-end wrench — firm enough to seal, never so hard that you risk damaging the valve or the caliper. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder and the banjo fittings at the caliper and master cylinder for weeping or dampness.
Test Before You Ride
The lever and pedal should feel firm and consistent, and neither should slowly sink while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Then, in a safe open area, test the brakes at low speed before riding normally.
When to Hand It to a Shop
Stop and get professional help if the lever will not firm up after several bleeding rounds, if it only firms up after pumping, if bubbles keep appearing no matter how long you bleed, or if you find fluid leaking from the master cylinder or a caliper. The same applies if the reservoir ran dry on an ABS-equipped bike, or if any part of the ABS unit or its lines was disconnected — that can trap air where a home bleed cannot reach it, and the system may need a dealer-level procedure or diagnostic tool to clear it properly.
Related Shopping Categories
Shop Brake Fluid for a 2021 Kawasaki EX400 - Ninja 400 Motorcycle.
Shop Brake Lines for a 2021 Kawasaki EX400 - Ninja 400 Motorcycle.
Shop Brake Pads for a 2021 Kawasaki EX400 - Ninja 400 Motorcycle.
Shop Stands for a 2021 Kawasaki EX400 - Ninja 400 Motorcycle.
Shop Brake Tools for a 2021 Kawasaki EX400 - Ninja 400 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.