Bleeding the Brakes on a 2021 Honda Africa Twin 1100 Adventure Sports ES
Shop parts for a 2021 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.What the Brake System on This Africa Twin Looks Like
The 2021 Honda Africa Twin 1100 Adventure Sports ES runs hydraulic disc brakes at both ends, each with its own master cylinder — the front fed by the lever on the right bar, the rear by the pedal on the right peg. Because both circuits are hydraulic, both are bled the same way, and both deserve attention when you service the system. This bike also carries an ABS system with an inertial measurement unit, which is the one detail that changes how you should think about the job. A routine flush through the caliper bleeders is well within reach of a home mechanic. Air that has worked its way into the ABS modulator itself is a different story, and that situation is covered further down.
Signs That the System Needs Bleeding
Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. That moisture lowers the fluid's boiling point, and a boiling fluid creates vapor that behaves exactly like air in the lines — the lever goes soft right when you need it most. Many riders refresh the fluid on a mileage or seasonal schedule for that reason alone, even with no symptoms at all.
Other triggers are more immediate. A lever that feels spongy or pulls closer to the grip than it used to, a rear pedal with a mushy, indefinite feel, or fluid in the reservoir that has turned dark or cloudy all point to a bleed. So does any job that opened the hydraulic system: new lines, a caliper rebuild, master cylinder work, or a fluid top-off after a leak. If you can see tiny bubbles in the reservoir when you work the lever, air is already in the circuit.
Tools and Supplies to Collect First
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container — opened fluid absorbs moisture, so buy what you need
- A box-end wrench that fits the bleeder valve snugly
- Clear tubing sized to grip the bleeder tightly, plus a catch bottle
- Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir
- The correct driver for the reservoir cap screws
- Optional: a one-way check-valve bleeder or a vacuum bleeder, both of which make a solo job far less fiddly
Setting Up Without Damaging the Bike
Get the machine upright and stable on a stand before you touch anything. For the front circuit, turn the bars so the reservoir on the bar sits level; a tilted reservoir spills the moment the cap comes off. Lay rags over the tank area, the plastics, the instrument cluster, and anything else below the reservoir, because brake fluid attacks paint and clear plastic on contact. If a drop lands where it shouldn't, wipe it up immediately and rinse the area with water rather than waiting until the end of the job.
The Bleeding Procedure, Step by Step
- Wipe the reservoir cap and surrounding area clean, then remove the cap and diaphragm.
- Use the syringe or baster to draw most of the old fluid out of the reservoir. Leave enough to cover the port at the bottom — never let the reservoir run dry, or you will pump air straight into the system.
- Top the reservoir with fresh fluid from the sealed container.
- Push the clear tubing onto the bleeder valve and route the other end into the catch bottle, with the bottle positioned so you can watch fluid move through the tube.
- Squeeze the lever (or press the pedal) and hold it steady.
- Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch for bubbles.
- Close the bleeder before you release the lever or pedal. Releasing first draws air back in past the threads.
- Repeat the squeeze–hold–open–close–release cycle, checking the reservoir level every few cycles and topping it off as needed.
- Keep going until the fluid coming through the tube is clean and completely free of bubbles, then close the bleeder.
- If your bike has two front calipers, bleed each one in turn rather than trying to do both at once. As a general practice, start with the caliper farthest from the master cylinder and work toward the closest.
Finishing the Job Correctly
Snug the bleeder down firmly without overtightening — you are sealing against a small seat, not torquing a structural bolt. Fill the reservoir to the level marking molded into the body, reinstall the diaphragm and cap, and wipe away every trace of spilled fluid. Then inspect the bleeder and the banjo fittings at the caliper and master cylinder for weeping; a dry paper towel pressed against each joint tells you quickly whether anything is seeping.
Testing Before You Ride
Work the lever and pedal several times. Both should feel firm and consistent, and neither should slowly sink while you hold steady pressure. Spin each wheel and listen — the brakes should not drag. Then ride slowly in a safe, open area and apply the brakes gently before trusting them at speed.
When to Stop and Take It to a Shop
If the lever will not firm up after several honest attempts, if it only firms after pumping, or if bubbles keep appearing no matter how long you bleed, something else is wrong. Fluid weeping from the master cylinder or a caliper, or a system that was run dry, opened at the ABS unit, or had the modulator disturbed, all call for a shop. The ABS modulator on this Africa Twin may need a dealer-level routine or diagnostic tool to purge air from it, and that is not a job to improvise. Hand it over rather than riding on a brake you cannot trust.
Related Shopping Categories
Shop Brake Fluid for a 2021 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.
Shop Brake Lines for a 2021 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.
Shop Brake Pads for a 2021 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.
Shop Stands for a 2021 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.
Shop Brake Tools for a 2021 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.