Bleeding the ABS Brakes on a 2020 Kawasaki KLE650 Versys ABS LT
Shop parts for a 2020 Kawasaki KLE650 - Versys ABS LT Motorcycle.
What You Are Working With on This Versys
The 2020 Kawasaki KLE650 Versys ABS LT uses hydraulic disc brakes at both ends, and the ABS designation confirms that an anti-lock braking system is part of the hydraulic layout. You have a front master cylinder at the lever, a rear master cylinder at the pedal, and calipers at the wheels. The front and rear circuits are separate hydraulic systems, so each one must be bled on its own. The ABS unit adds internal valves and passages, but for routine fluid refresh and air removal at the calipers, a normal bleed through the caliper bleeders is the starting point. If air has entered the ABS unit itself—because a reservoir ran dry, a line was disconnected, or ABS hardware was serviced—the job changes and should go to a shop with the appropriate diagnostic equipment.
When a Brake Bleed Is Due
A spongy or soft lever, a pedal that feels vague, or a lever that now pulls closer to the grip than it used to are classic signs that air or old fluid is affecting the system. Dark or cloudy fluid in the reservoir is another prompt. A bleed is also due after any work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work. Even without symptoms, brake fluid absorbs moisture over time, which lowers its boiling point and can lead to brake fade under hard use. Many riders refresh the fluid on a regular schedule for that reason alone. On this Versys, treat the front and rear as two separate service items and plan to bleed both if you are refreshing the fluid.
Tools and Supplies to Stage First
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- Clear tubing that fits snugly over the bleeder valve
- A catch bottle for old fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder can make the job easier when you are working alone, but the basic lever-and-bleeder method works fine with a helper or with patience. Keep the catch bottle lower than the bleeder so fluid and air flow away from the caliper.
Preparation Before Opening the Hydraulic System
Support the bike securely upright on a stand so it cannot tip while you are working at the lever, pedal, and calipers. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Clean around the reservoir cap before removing it so dirt does not fall into the fluid. Have your fresh fluid open and ready before you start, and keep the reservoir cap and diaphragm clean and close at hand.
Bleeding the Front and Rear Circuits
Work one hydraulic circuit at a time. Use only fresh fluid from a sealed container, and use the fluid type marked on the reservoir cap. As a general practice, start with the caliper farthest from its master cylinder. If your bike has two front calipers, treat each one as its own bleed point and finish one completely before moving to the other. The rear circuit is bled at the rear caliper in the same basic way.
- Remove the reservoir cap and diaphragm. Use a syringe or turkey baster to remove most of the old fluid from the reservoir, but leave enough that you do not draw air into the master cylinder. Wipe the reservoir neck clean.
- Refill the reservoir with fresh fluid to the level marking. Keep the reservoir open while you bleed, and check the level after every few bleed cycles.
- Fit the box-end wrench to the bleeder valve. Push the clear tubing onto the bleeder snugly and route the other end into the catch bottle.
- For the front circuit, squeeze the lever slowly and hold it firm. For the rear circuit, press the pedal and hold it. Do not pump rapidly; a steady squeeze or press gives you better control of the fluid and air.
- With the lever or pedal held, open the bleeder about a quarter turn. Let fluid and air flow out through the tube. Watch the tubing for bubbles and for the color of the fluid.
- Close the bleeder before you release the lever or pedal. This is the critical step that prevents air from being drawn back into the caliper.
- Release the lever or pedal slowly. Check the reservoir level and top it off before it gets low. Repeat the squeeze-hold-open-close-release sequence until fresh, clean, bubble-free fluid comes through the tube.
- If you have a second front caliper, repeat the same sequence on that caliper. Then repeat the process at the rear caliper for the rear circuit. Keep topping off the reservoir throughout so it never runs low enough to pull air into the system.
- When clean fluid is confirmed at the bleeder, close it snugly without overtightening. Remove the tubing and wipe the bleeder clean.
Finishing Up and Checking for Leaks
Fill the reservoir to the correct level marking, then reinstall the diaphragm and cap. Clean any spilled fluid from the reservoir, caliper, and surrounding parts. Check the bleeder valves and the banjo fittings at the master cylinder and calipers for leaks. A dry fitting after several firm lever or pedal applications is what you want to see. If you find weeping fluid, stop and correct it before riding.
Testing Before You Ride
The lever and pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally. If the lever or pedal changes feel after the test, or if either one needs pumping to come up, do not ride the bike until the problem is resolved.
If the Brakes Will Not Firm Up
A lever or pedal that will not firm up after several bleeding attempts, a lever that firms only after pumping, persistent air bubbles, or fluid leaking from the master cylinder or caliper are reasons to stop and have the system inspected. Because this Versys has ABS, any situation where air may have entered the ABS unit—especially if a reservoir ran dry or an ABS line was disconnected—should go to a shop. Do not ride with compromised brakes or guess at an ABS bleed procedure.
Related Shopping Categories
Shop Brake Fluid for a 2020 Kawasaki KLE650 - Versys ABS LT Motorcycle.
Shop Brake Lines for a 2020 Kawasaki KLE650 - Versys ABS LT Motorcycle.
Shop Brake Pads for a 2020 Kawasaki KLE650 - Versys ABS LT Motorcycle.
Shop Stands for a 2020 Kawasaki KLE650 - Versys ABS LT Motorcycle.
Shop Brake Tools for a 2020 Kawasaki KLE650 - Versys ABS LT Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.