Bleeding the Brakes on a 2017 Honda Africa Twin CRF1000L
Shop parts for a 2017 Honda Africa Twin Motorcycle.The 2017 Honda Africa Twin CRF1000L uses hydraulic disc brakes at both ends, and this model year is ABS-equipped. That means the front lever and the rear pedal each move fluid through a sealed hydraulic circuit, and a routine bleed is the correct way to refresh old fluid and push out air. If your bike has two front calipers, treat each caliper as its own bleed point and work through them one at a time. The rear brake is hydraulic as well, so it gets its own bleed at the rear caliper. Because this Africa Twin has ABS, a normal bleed through the caliper bleeders is generally enough for fluid service, but air trapped inside the ABS unit itself is a different job and should go to a shop.
When a Bleed Is Due
A spongy lever or pedal is the classic sign that air is in the system or that the fluid is past its useful life. You may also notice the front lever pulling closer to the grip than it used to, a pedal that feels soft before it bites, or fluid in the reservoir that looks dark or cloudy instead of clear. Any job that opened the hydraulic system—new brake lines, caliper service, or master cylinder work—should be followed by a bleed before the bike is ridden normally.
Even without symptoms, brake fluid absorbs moisture from the air over time. That moisture lowers the fluid’s boiling point, which can lead to brake fade under hard or repeated use. Many riders refresh the fluid on a regular schedule as preventive maintenance, especially on a bike like the Africa Twin that may see loaded touring, two-up riding, or long descents. If the lever and pedal feel firm and the fluid looks clean, a bleed can wait, but it should not be ignored indefinitely.
Tools and Supplies to Stage First
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- A length of clear tubing that fits snugly over the bleeder
- A catch bottle for the old fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder can make the job easier for one person, but the manual lever-and-bleeder method works fine with a little patience. Use only fluid from a sealed container, and keep the cap on the container when it is not being poured. Have more rags on hand than you think you need.
Prepare the Bike and Protect the Finish
Support the Africa Twin securely upright on a stand so the reservoirs sit at a stable angle. Turn the handlebars so the front reservoir is level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a drop lands on a painted or plastic surface, wipe it up immediately and rinse the area with water.
Clean the area around the reservoir cap before removing it so dirt does not fall into the fluid. Remove the cap and diaphragm carefully, set them on a clean rag, and keep the reservoir upright throughout the job. Do not pump the lever or pedal with the reservoir cap off and the fluid level low, because that can draw air into the system.
Step-by-Step Bleeding Procedure
- Open the front reservoir and use a syringe or turkey baster to remove most of the old fluid. Leave enough fluid in the bottom so the master cylinder does not draw air, but remove the dark or cloudy portion.
- Refill the reservoir with fresh fluid of the type marked on the cap. Keep the fluid level well above the lower marking as you work.
- Attach the clear tubing to the front caliper bleeder and route the other end into the catch bottle. The tubing should fit snugly so air cannot leak past the bleeder threads.
- Squeeze and hold the front lever. With the lever held, open the bleeder about a quarter turn and let fluid and air escape through the tube.
- Close the bleeder before releasing the lever. Releasing the lever with the bleeder open can pull air back into the caliper.
- Repeat the squeeze-hold-open-close-release sequence until fresh, clean, bubble-free fluid comes through the tube. Check the reservoir often and top it off before it gets low.
- If your bike has two front calipers, bleed one caliper at a time. As a general practice, start with the caliper farthest from the master cylinder by hose routing, then move to the other caliper and repeat the same sequence.
- Move to the rear brake. Open the rear reservoir, remove most of the old fluid, and refill with fresh fluid. Attach the clear tube to the rear caliper bleeder and route it to the catch bottle.
- Press and hold the rear pedal, open the bleeder about a quarter turn, then close it before releasing the pedal. Repeat until the fluid runs clean and free of bubbles, topping off the rear reservoir as needed.
- Keep the reservoir from running dry at every stage. If the level drops low enough to draw air, you will have to start over and may push air into a place that is difficult to remove.
Finishing, Leak Checks, and Test Ride
When clean fluid is flowing and no bubbles remain, tighten the bleeder snugly without overtightening. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe away any spilled fluid. Check for leaks at the bleeder and at the banjo fittings on the caliper and master cylinder. A dry fitting after several lever or pedal applications is a good sign.
Before riding, the front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally. If anything feels soft or inconsistent, do not ride the bike until the problem is resolved.
If the Brakes Will Not Firm Up
A lever that will not firm up after several bleeding attempts, a lever that firms up only after pumping, persistent air bubbles, or fluid leaking from the master cylinder or caliper are reasons to stop and diagnose the problem. On an ABS-equipped Africa Twin, if the reservoir ran dry, the ABS unit or its lines were disconnected, or you suspect air has entered the ABS unit itself, the bike should go to a shop. A standard caliper bleed may not remove air from that part of the system, and riding with a spongy brake is not worth the risk.
Related Shopping Categories
Shop Brake Fluid for a 2017 Honda Africa Twin Motorcycle.
Shop Brake Lines for a 2017 Honda Africa Twin Motorcycle.
Shop Brake Pads for a 2017 Honda Africa Twin Motorcycle.
Shop Stands for a 2017 Honda Africa Twin Motorcycle.
Shop Brake Tools for a 2017 Honda Africa Twin Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.