How to Bleed the Front Brake on a 1979 Kawasaki KZ400
Shop parts for a 1979 Kawasaki KZ400 Motorcycle.The 1979 Kawasaki KZ400 uses a hydraulic disc brake up front and a mechanical drum brake at the rear. That distinction matters before you start: this article covers bleeding the front hydraulic system only. The rear drum is operated by a cable or rod and does not use brake fluid, so it is adjusted rather than bled. The KZ400 predates ABS and linked brakes, so there is no module or distribution block to complicate the job. The job is straightforward: push fresh fluid through the front caliper while expelling trapped air and old fluid.
When the KZ400 Front Brake Needs Attention
Bleed the front brake when the lever feels spongy or soft, when it pulls closer to the grip than it used to, or when the fluid in the reservoir looks dark or cloudy. It is also required after any work that opened the hydraulic system, such as replacing a brake line, servicing the caliper, or repairing the master cylinder. Even without symptoms, brake fluid absorbs moisture from the air over time. That moisture lowers the fluid’s boiling point and can contribute to brake fade, so many riders refresh the fluid on a regular schedule. If you are unsure when the fluid was last changed, a bleed is cheap insurance.
Tools and Supplies to Have Ready
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the front caliper bleeder valve
- A length of clear tubing that fits snugly over the bleeder
- A clean catch bottle for the old fluid
- Rags or shop towels, plus water for rinsing spills
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver that fits the reservoir cap screws
A one-way check-valve bleeder or vacuum bleeder can make solo work easier, but the manual method works fine.
Setting Up and Protecting the Bike
Support the KZ400 securely upright on a stand so it cannot tip while you are working the lever. Turn the handlebars until the front master cylinder reservoir sits level; a tilted reservoir is hard to fill accurately and easy to spill. Cover the painted surfaces, plastic panels, and the instrument area with rags before you open anything. Brake fluid damages paint and plastic, so wipe spills immediately and rinse with water.
Bleeding the Front Brake, Step by Step
- Clean the top of the master cylinder reservoir so dirt cannot fall in, then remove the cap and diaphragm with the correct screwdriver.
- Use the syringe or turkey baster to remove most of the old fluid from the reservoir. Leave the bottom of the reservoir covered so you do not push a slug of air into the system, but remove as much dark or cloudy fluid as you can.
- Refill the reservoir with fresh fluid of the type marked on the cap. Keep the container sealed and clean; do not reuse fluid that has been sitting open.
- Slip the clear tubing over the front caliper bleeder valve and route the other end into the catch bottle. Position the box-end wrench on the bleeder so you can open and close it smoothly.
- Squeeze the front brake lever slowly and hold it firmly. Do not pump it rapidly; a steady squeeze moves fluid and air more predictably.
- With the lever held, open the bleeder about a quarter turn. You should see fluid and possibly air bubbles move through the clear tubing. Close the bleeder before you release the lever.
- Release the lever slowly, then check the reservoir level and top it off with fresh fluid. Never let the reservoir run low enough to draw air in through the master cylinder.
- Repeat the squeeze-hold-open-close-release sequence until the fluid coming through the tubing is clean and free of bubbles. Keep topping off the reservoir after every few strokes. On a multi-caliper front end, bleed each caliper separately, starting farthest from the master cylinder.
- When the fluid runs clear and bubble-free, hold the lever, close the bleeder snugly, and remove the tubing. Tighten the bleeder firmly but do not overtighten it; you are sealing against a small seat, not cranking a lug nut.
Finishing the Job Correctly
Fill the reservoir to the correct level marking with fresh fluid, then reinstall the diaphragm and cap. Wipe down the caliper, bleeder, and reservoir area with a clean rag, and rinse away any brake fluid that touched paint or plastic. Check for leaks at the bleeder valve and at the banjo fittings on the caliper and master cylinder. A weep or wet film means something needs attention before riding.
Testing the Brake Before Riding
The front lever should feel firm and consistent, not spongy, and it should not slowly sink while you hold steady pressure. Spin the front wheel and confirm the brake is not dragging; a slight pad rub is normal, but the wheel should still turn freely. With the bike off the stand and in a safe, low-speed area, test the brake gently before riding normally. If it feels different at low speed, stop and investigate.
Troubleshooting and When to Stop
If the lever will not firm up after several bleeding attempts, if it firms only after you pump it, or if bubbles keep appearing no matter how long you bleed, air is still getting in or the master cylinder or caliper has a problem. Fluid leaking from the master cylinder, caliper, or fittings is another reason to stop. This KZ400 has no ABS or linked-brake hardware, so there is no special sequence to follow, but a persistent soft lever is still not something to ignore. Take it to a qualified shop if the lever will not hold pressure, a leak cannot be traced, or you are not confident the system is sealed.
Related Shopping Categories
Shop Brake Fluid for a 1979 Kawasaki KZ400 Motorcycle.
Shop Brake Lines for a 1979 Kawasaki KZ400 Motorcycle.
Shop Brake Pads for a 1979 Kawasaki KZ400 Motorcycle.
Shop Stands for a 1979 Kawasaki KZ400 Motorcycle.
Shop Brake Tools for a 1979 Kawasaki KZ400 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.