Skid Lid Traditional Helmet

$49.99 - $54.99
4.00 out of 5 stars

This Purchase Qualifies For:

  • Description
  • Reviews (2)
  • Q&A (0)
  • Sizing Chart
  • Contoured helmet with a low-profile fit
  • "Skid Lid Original" with added visor
  • Thermoplastic alloy injected shell
  • Retention straps with D-rings
  • Ear straps covered for comfort
  • Meets or exceeds D.O.T. standards
4.0 out of 5 stars (2)
4.0 out of 5 stars
5 star   2
4 star 0
3 star 0
2 star   1
1 star 0
See Terms and Conditions
1-2 of 2
Overall 2 out of 5 stars
Sizing - Fit true to size?
Verified Purchaser
Skid lid

I just didn't like much about the helmet so I returned it today. It fit like it was oval shaped and I had a hard time with the chin strap.

Overall 5 out of 5 stars
Sizing - Fit true to size?
Location: Medina, Ohio
Best Buy

What I wanted:
Clean look, low wind drag, Just out for the ride look, and a value price. From placement of order to receiving was 4 days. Item was fine when received. Fit is just great. When riding the helmet is great from 0 MPH to 110 MPH for over 5 min no fit problems and wind drag was very, very low. A very good selection for the low lean looking rider

sandman111 Dyna
1-2 of 2
Total Questions (0)
Questions with answers:
Questions without answers:
SizeHead Circumference
3X-Small 19.25 - 19.625in (48.9 - 49.8cm)
2X-Small 20.125 - 20.5in (51.1 - 52.1cm)
X-Small 20.875 - 21.25in (53.0 - 54.0cm)
Small 21.625 - 22in (54.9 - 55.9cm)
Medium 22.5 - 22.875in (57.1 - 58.1cm)
Large 23.25 - 23.625in (59.1 - 60.0cm)
X-Large 24 - 24.375in (61.0 - 61.9cm)
2X-Large 24.75 - 25.25in (62.9 - 64.1cm)
3X-Large 25.625 - 26in (65.1 - 66.0cm)


1. Measure your head size. To do this, pass a tape measure horizontally around your head at a height of about one inch above your eye- brows. When done properly, you will have measured the largest part of your head.

2. Check your measurement with the helmet sizing chart and select the closest size. As the helmet may not always meet your head size exactly, and your head measurement may fall between two sizes, first try the smaller size.


1. Expand the helmet opening by pulling outwards on each chinstrap, and slide your head into the helmet. If you are unfamiliar with helmets you may be reluctant to pull the helmet down, as it may feel too tight. Even if the helmet is difficult to put on, please use the smallest helmet possible. The helmet should feel snug. If the helmet is not tight, it is too big for you. New helmets will break in and loosen slightly over time.

2. Once the helmet is on:

  • Check that the helmet inner lining fits snugly all around your head.
  • Check that the top pad presses on the top of your head.
  • Check that the cheek pads press up against your cheeks. When you open and close your mouth, you should drag your teeth along the inside of your cheeks.
  • Check to make sure that you cannot easily slide your finger into the helmet along the side of your temple.
  • Hold the helmet with one hand on each side. Without moving your head, try to move the helmet up and down, and side to side. You should feel the skin of your head and face being pulled as you try to move the helmet. If you can move the helmet around easily, it is too big. Try a smaller size. Please note that during this check, the chinstraps should be properly fastened.