EVS T7 Martini Helmet

$169.99
$109.97 (35% off)
4.30 5 3
4.30 out of 5 stars

This Purchase Qualifies For:

 
  • Description
  • Reviews (3)
  • Q&A (1)
  • Sizing Chart

The T7 Helmet is a lightweight polycarbonate helmet with increased ventilation for maximum airflow. It features a RAM air cooling system with internal EPS ventilation channels and a removable, washable moisture wicking internal liner.

  • Lightweight polycarbonate shell: 1632 grams.
  • RAM air cooling system.
  • Internal EPS ventilation channels.
  • Four intake and six exhaust ports for maximum airflow.
  • Removable / washable moisture-wicking comfort liner.
  • SNELL, DOT and ECE certified.
4.3 out of 5 stars (3)
4.3 out of 5 stars
5 star   1
4 star   2
3 star 0
2 star 0
1 star 0
See Terms and Conditions
1-3 of 3
Overall 5 out of 5 stars
Comfort
Performance
Sizing - Fit true to size?
Style
Weight
Verified Purchaser
Jerrod

Nice helmet worth the 110 bucks for sure

Overall 4 out of 5 stars
Comfort
Performance
Sizing - Fit true to size?
Style
Weight
Top 1000 Contributor Verified Purchaser
Location: São Paulo, Brazil
Melo
Nice but heavy

The EVS Helmet have a very good visual, finish, perfect size and fit, is very good for any goggles and is safe, but is heavy and after to race gets tired...but the price is very honest.

Overall 4 out of 5 stars
Comfort
Performance
Sizing - Fit true to size?
Style
Weight
Location: Atascadero, Ca
BermBlaster414
EVS T-7 Helmet

I like the style of the helmet alot. Usually I wear a Large helmet but this one seems a little snug. Mostly, I think its the cheek pads. Im gonna wear it some and hope they smash down a bit. Overall it looks like a quality product and you can't beat the price!

1-3 of 3
Total Questions (1)
Questions with answers:
  1
Questions without answers:
0
1-1 of 1
trent 1 year 5 months ago
Is there a medium size in the black evs helmet?
MotoSport Staff Expert Top 1 Contributor
1 year 5 months ago
MotoSportGrantK
Unfortunately EVS has phased out the T7 Martini Helmet so the only helmets available will be whats listed.
1-1 of 1
EVS HELMETS
SizeHead CircumferenceHat Size
X-Small 21.2" - 21.6" (53 - 54 cm) 6 - 6 3/8
Small 21.7" - 22" (55 - 56 cm) 6 3/4 - 6 7/8
Medium 22.4" - 22.8" (57 - 58 cm) 7 - 7 1/8
Large 23.2" - 23.6" (59 - 60 cm) 7 1/4 - 7 3/8
X-Large 24" - 24.4" (61 - 62 cm) 7 1/2 - 7 5/8
2X-Large 24.8" - 25.2" (63 - 64 cm) 7 3/4 - 7 7/8

MEASURING INSTRUCTIONS

1. Measure your head size. To do this, pass a tape measure horizontally around your head at a height of about one inch above your eye- brows. When done properly, you will have measured the largest part of your head.

2. Check your measurement with the helmet sizing chart and select the closest size. As the helmet may not always meet your head size exactly, and your head measurement may fall between two sizes, first try the smaller size.

WHEN YOU RECEIVE YOUR HELMET

1. Expand the helmet opening by pulling outwards on each chinstrap, and slide your head into the helmet. If you are unfamiliar with helmets you may be reluctant to pull the helmet down, as it may feel too tight. Even if the helmet is difficult to put on, please use the smallest helmet possible. The helmet should feel snug. If the helmet is not tight, it is too big for you. New helmets will break in and loosen slightly over time.

2. Once the helmet is on:

  • Check that the helmet inner lining fits snugly all around your head.
  • Check that the top pad presses on the top of your head.
  • Check that the cheek pads press up against your cheeks. When you open and close your mouth, you should drag your teeth along the inside of your cheeks.
  • Check to make sure that you cannot easily slide your finger into the helmet along the side of your temple.
  • Hold the helmet with one hand on each side. Without moving your head, try to move the helmet up and down, and side to side. You should feel the skin of your head and face being pulled as you try to move the helmet. If you can move the helmet around easily, it is too big. Try a smaller size. Please note that during this check, the chinstraps should be properly fastened.