AFX North America Inc. is a family-owned and operated manufacturer of motorcycle, ATV, scooter and snowmobile helmets. Established in 1996, the Cerritos (CA, USA) and London (ON, Canada) based company has enjoyed exceptional growth and currently stands as one of the top helmet suppliers for the North American market.
Shell Design: An aerodynamic shell design constructed using an advanced lightweight composite poly-alloy.
Face Shield: A flush-fit, built in side-cover style face shield that is optically correct, compound-curved, scratch-resistant and protects against UV-rays. Shield can be removed to allow open face riding or for use with most goggles. Optional outer shield, three-position 9 cm (3.5")long shield mounted on outside of the clear shield and moving independently from the clear shield. Will also work with the visor removed and the street side covers installed.
Ventilation: Nine points of ventilation with chin, side, forehead, top and rear vent. Three intake vents and six exhaust vents.
Visor: A removable and adjustable (30 mm) screw-on visor. Shield can also be used without the visor. Side cover kit included.
Retention system is D-Ring.
Provides ample ear cavity space for most speaker systems.
There are four tinted shields available for this model (all sold separately).
A clear coat finish to protect paint and graphics.
A large-size FX-39DS weighs 1.59 kg or 3.50 pounds.
This helmet model meets or exceeds both ECE 22.05 (size XS - XXL) and DOT FMVSS-218 (size XS - XXXXL) motorcycle helmet safety standards.
Notes: Ships with a Clear face shield. The fit of the helmet can be customized by replacing your existing cheek pads with thinner cheek pads (for a looser fit) or thicker cheek pads (for a tighter fit). The fit can also be customized by replacing your existing comfort liner with a thinner comfort liner (for a looser fit) or thicker comfort liner (for a tighter fit).
There have been no questions asked about the AFX FX-39DS Series 2 Helmet.
21 1/4" - 21 5/8" (54 - 55 cm)
6 3/4 - 7 7/8
22" - 22 7/16" (56 - 57 cm)
7 - 7 1/8
22 13/16" - 23 1/4" (58 - 59 cm)
7 1/4 - 7 3/8
23 5/8" - 24" (60 - 61 cm)
7 1/2 - 7 5/8
24 3/8" - 24 13/16" (62 - 63 cm)
7 3/4 - 7 7/8
25 3/16" - 25 5/8" (64 - 65 cm)
8 - 8 1/8
26" - 26 3/8â€%9D (66 - 67 cm)
8 1/4 - 8 3/8
26 3/4" - 27 1/8" (68 - 69 cm)
8 1/2 - 8 5/8
20 7/8" - 21 1/4" (53 - 54 cm)
6 5/8 - 6 3/4
21 1/4" - 21 5/8" (54 - 55 cm)
6 3/4 - 6 7/8
21 5/8" - 22" (55 - 56 cm)
6 7/8 - 7
1. Measure your head size. To do this, pass a tape measure horizontally around your head at a height of about one inch above your eye brows. When done properly, you will have measured the largest part of your head.
2. Check your measurement with the helmet sizing chart and select the closest size. As the helmet may not always meet your head size exactly, and your head measurement may fall between two sizes, first try the smaller size.
WHEN YOU RECEIVE YOUR HELMET
1. Expand the helmet opening by pulling outwards on each chinstrap, and slide your head into the helmet. If you are unfamiliar with helmets you may be reluctant to pull the helmet down, as it may feel too tight. Even if the helmet is difficult to put on, please use the smallest helmet possible. The helmet should feel snug. If the helmet is not tight, it is too big for you. New helmets will break in and loosen slightly over time.
2. Once the helmet is on:
Check that the helmet inner lining fits snugly all around your head.
Check that the top pad presses on the top of your head.
Check that the cheek pads press up against your cheeks. When you open and close your mouth, you should drag your teeth along the inside of your cheeks.
Check to make sure that you cannot easily slide your finger into the helmet along the side of your temple.
Hold the helmet with one hand on each side. Without moving your head, try to move the helmet up and down, and side to side. You should feel the skin of your head and face being pulled as you try to move the helmet. If you can move the helmet around easily, it is too big. Try a smaller size. Please note that during this check, the chinstraps should be properly fastened.