Thor is the originator of motocross apparel. Thor is a hardcore, grass roots company that is continued proof of what it takes to reach the top and more importantly, how to stay there. It is the only company with over 40 years of experience in the motocross marketplace. Thor prides itself on key selling features like quality, strength and performance. Thor is more than a brand. It's a lifestyle.
Reinforced chin bar for increased strength.
High-flow mouth vent with filter to prevent roost from entering.
Fully adjustable visor provides ample coverage.
Front intake vents allow direct airflow to enter the helmet.
Minimal gaskets reduce the overall helmet weight.
Antibacterial, moisture-wicking, removable and washable Silvercool liner for comfort.
Dual-density EPS liner features extensive venting that aligns with shell vent ports.
Hand-laid composite fiberglass construction for superior strength with minimal weight.
Rear exhaust vents allow hot air to escape quickly.
Rear shell shape quickly and easily repositions the goggle strap.
Side vents funnel cooler air into the helmet.
Large hole mesh liner promotes airflow.
DOT and ECE 22.05 approved.
Meets AMA and FIM requirements for helmets used in competition.
Write a Review
Enter to Win $500
Write your review and you'll automatically be entered in our monthly drawing. Include an image or video to DOUBLE your chances to win!
A: Yes you could. Feel free to give us a call at 888-676-8853 and we would be happy to help you out with your order.
1-1 of 1
20 - 20 1/2" (51 - 52 cm)
6 3/8 - 6 1/2
20 3/4 - 21 1/4" (53 - 54 cm)
6 5/8 - 6 3/4
21 5/8 - 22" (55 - 56 cm)
6 7/8 - 7
22 1/2 - 23 3/4" (57 - 58 cm)
7 1/8 - 7
23 1/4 - 23 5/8" (59 - 60 cm)
7 3/8 - 7 1/2
24 - 24 11/2" (61 - 62 cm)
7 5/8 - 7 3/4
24 3/4 - 25 5/8" (63 - 64 cm)
7 7/8 - 8
5 - 6
20 5/8" (49 - 50 cm)
6 1/8 - 6 1/4
6 - 8
21 1/8" (51 - 52 cm)
6 3/8 - 6 1/2
8 - 10
21 1/4" (53 - 54 cm)
6 5/8 - 6 3/4
10 - 12
21 5/8" (55 - 54 cm)
6 7/8 - 7
1. Measure your head size. To do this, pass a tape measure horizontally around your head at a height of about one inch above your eye brows. When done properly, you will have measured the largest part of your head.
2. Check your measurement with the helmet sizing chart and select the closest size. As the helmet may not always meet your head size exactly, and your head measurement may fall between two sizes, first try the smaller size.
WHEN YOU RECEIVE YOUR HELMET
1. Expand the helmet opening by pulling outwards on each chinstrap, and slide your head into the helmet. If you are unfamiliar with helmets you may be reluctant to pull the helmet down, as it may feel too tight. Even if the helmet is difficult to put on, please use the smallest helmet possible. The helmet should feel snug. If the helmet is not tight, it is too big for you. New helmets will break in and loosen slightly over time.
2. Once the helmet is on:
Check that the helmet inner lining fits snugly all around your head.
Check that the top pad presses on the top of your head.
Check that the cheek pads press up against your cheeks. When you open and close your mouth, you should drag your teeth along the inside of your cheeks.
Check to make sure that you cannot easily slide your finger into the helmet along the side of your temple.
Hold the helmet with one hand on each side. Without moving your head, try to move the helmet up and down, and side to side. You should feel the skin of your head and face being pulled as you try to move the helmet. If you can move the helmet around easily, it is too big. Try a smaller size. Please note that during this check, the chinstraps should be properly fastened.