MSR Brake Saver

$7.95
4.40 5 10
4.40 out of 5 stars
In Stock
 
MSR Brake Saver
MSR Brake Saver
  • Description
  • Reviews (10)
  • Q&A (2)
  • Save your rear brake from catastrophic damage during your bar to bar battles by installing the MSR brake saver.
  • A universal design allows the MSR brake saver to be installed on virtually any dirt bike.
  • MSR covered the wire with a plastic housing to prevent the brake saver from damaging your dirt bike.
4.4 out of 5 stars (10)
4.4 out of 5 stars
5 star   8
4 star 0
3 star   1
2 star 0
1 star   1
See Terms and Conditions
1-10 of 10
Overall 5 out of 5 stars
Durability
Ease of Installation
Performance
Style
Verified Purchaser
Location: up north
2moose1

Have one of these on every bike I ve owned. I ride a lot of woods and trails

Overall 5 out of 5 stars
Top 500 Contributor
Location: DAMASCUS, OR
STEAMIN711
GREAT AT WHAT IT DOES

FIT PERFECT. LOOKS GOOD.

Overall 3 out of 5 stars
Top 500 Contributor Top 250 Contributor
Location: Bensalem, PA
barratt88
So far so good.

Havent had any pedal issues yet. just put on in case and is easy to install and doesnt effect brake function at all.

Overall 5 out of 5 stars
Durability
Ease of Installation
Performance
Style
Top 500 Contributor Top 1000 Contributor
Location: hawaii
kufd
Great!

very easy install, so long you have a aftermarket skid plate, it will lace right through, and all you have to do is crimp the copper sleave. will hold break pedal in location best as possible, during trail runs and close bike to bike races

Overall 5 out of 5 stars
Durability
Ease of Installation
Performance
Style
Top 100 Contributor Top 250 Contributor
Location: Watkinsville, Ga
DirtRider348
Order it!

My friend installed this on his 07' limited editionYZ250 for trail riding and he nicked a tree with the brake pedal. Brake saver saved the brake from completly bending out! Great buy!
Avery348

Overall 5 out of 5 stars
Durability
Ease of Installation
Performance
Style
Top 500 Contributor
Location: boulder creek, california
crman
Good product.

i've been using these since 1998. these really are brake savers like they say. very simple yet effective. i have still bent my brake levers in a crash but it was still usable. i put these on all my dirtbikes.

Overall 5 out of 5 stars
Top 25 Contributor Top 50 Contributor
Location: Southampton, MA
livinloud22
ORDER ONE NOW!

easy to use and great!!!! confused by the look of it? heres how it works: when you get it you slip the metal loop apart and slide the plastic wire guard off. you drill a hole in your foot brake and slide the wire through til the metal stop reaches the brake pedal, slide the plastic cover back on and loop the wire around your frame. then reinstall the metal clip/crimp. crimp it down tight onto the wire and then ride! if anything snags you pedal it will only bend as far as you allow it to(adjust wire when installing to help this) $5 now or $150 later for a new brake pedal!? you decide

Overall 1 out of 5 stars
Top 500 Contributor
Location: Miami
Jethro
Cheap

yes it is cheap I didn't like the fact that doesn't comes with the oval type predrill washer that you install on the frame to tie off the cable instead you are supouse to run the cable around the engine mount not a wise design
I'll prefer paying few more dollars and get a complete system not a incomplete kind a tie it off were ever you can!!!
I trew it to te garbish simple as that

Overall 5 out of 5 stars
Top 500 Contributor Top 1000 Contributor
Location: Ridgefield, CT
KTMRider
Great buy

i think this thing cost me like $5, and its saved me from having to buy $100 worth of brake levers. if you ride like you stole it and crash a lot, this is definatly worth the $5.

Overall 5 out of 5 stars
Top 100 Contributor Top 250 Contributor
Location: Centralia, WA
Jesse
Cheap protection

This product installs super easy and does a good job of protecting your brake pedel.

1-10 of 10
Total Questions (2)
Questions with answers:
  2
Questions without answers:
0
1-2 of 2
Syork Over 7 years ago
Where does the MSR brake saver attach on the pedal and bike?
MotoSport Staff Expert
Over 7 years ago
james718
one end loops on the brake pedal tip and the other end needs to be attached to the frame. I've attached it to the bolt that hold the engine guard on.
Top 500 Contributor
Over 5 years ago Location: boulder creek, california
crman
yes. i drill a hole in the brake pedal and attach one end there, then i usually attach the other end to my skid plate via a bolt with a hole drilled through it, this makes removing the skid plate quicker.
ryan079 Over 7 years ago
How does it work??
how does that keep u from bending your brake pedal
MotoSport Staff
Over 7 years ago Location: Portland, OR
Drewski
It doesn't keep you from bending or breaking your peddle. It's mainly designed to limit the bend if the peddle take a hard enough impact. Basically it just connects to the peddle and then to your frame and limits how far the lever will bend outwards, and downwards..
Top 500 Contributor
Over 5 years ago Location: boulder creek, california
crman
it doesn't completley stop bending but it keeps the pedal in a usuable area so the race can go on without having to stop and bend it back. plus it prevents brush, like manzanita, from going inbetween the brake lever and engine case.
1-2 of 2