Had to modify the cable connectors to match my bike but once installed it worked great. No more super fast flashing turn signals
Lockhart Phillips Universal LED Turn Signal Flasher Relay
Write your review and you'll automatically be entered in our monthly drawing. Include an image or video to DOUBLE your chances to win!Write Your Review
Picture shows a quick connect, but it comes in a package with two posts. Also, there's no way to secure it to the original location on my '15 R6. I would recommend a TST instead to fit the stock location
Probably the easiest thing to install on the bike (took about 30 seconds). You just plug it in and you're in business. As expected, it successfully slowed down my integrated sequential tail light flash rate. My only gripe is that it made my front led turn signals a tad faster, which isn't so major. Overall, it seems like a quality product and I'm happy with it.
I had a different brand relay that burnt out after one season,and bought this one to compare. So far, so good. Note: picture shows quick connect, mine, however, did not come this way so I had to cut the end off my burnt out one.
No surprises here, used with my front turn signals.
Needed a flasher relay that would work with new LED turn signals on my DR-Z400S dual sport.
This one worked perfectly, and was a piece of cake to install. Was able to wire it in such as way as to allow me to easily flip back to the OEM flasher if necessary.
Great price, too.
Much better solution than heat-generating, current-sucking load resistors, IMHO.
Plugged It in and worked fine ! But a minute later It stopped working ?! Is it possible the relay gave out because my blinkers stopped blinking :(
This thing works GREAT ! ! I had installed the HotBodies flush mount turn signals on my 07 Gixxer 6, and had the fast flash issue since they were LED, once I figured out what wires to pull out of the relay and hook this one up to it was done in a "flash". Took about 10 minutes to install and works amazingly, No problems ! !
I tried a regular flasher using resistors and it would not work. I then tried this one and it worked perfect with my low amp LED's.
it was a little hard to find out how to install but once I did fixed the fast flash issue
RIGHT ON!!! Soon as i got it, i slapped it on my YZF600R and couldn't be happier. Was as easy as lifting the seat, unplugging original relay and plug in the LP aftermarket. My undertail is finally complete!
It was exactly what i needed after my HB flushmounts and undertail...Take off 8 bolts and then it is right there! no more fast flash rate.
2002 cbr 600f4i
I bought this relay for my 04 gsxr 600 that had LED rear turn signals when I bought it. I purchased this and the LP integrated tail light. I understand that this part is a universal fit, but some (any) instructions would be nice, at least how they want installed in the system.
Once I figured out where to splice this in on my bike, the only modification for me was to cut the terminals off that came with it and use some smaller ones to keep it plug-and-play. The relay DOES WORK at slowing down the blink rate to around normal, HOWEVER it made the LEDs about 50% dimmer than without the relay in the system. The front OEM signals still seemed to be about the normal brightness. Maybe this is just the way it works on this bike as again, it is universal. Overall It does work as intended to slow down the blink rate but I'd rather have a fast blink rate with bright lights than a slow blink rate with lights that can't be seen.
my relay is dropping the voltage so much my signals hardly work.
This is a very Item with the LED Lights but it came with no Instructions, but was able to tell which wire needed to go. It very possible that you will have to splice some wires, but other than not bad.
This relay works great once it is installed however installation is the problem. Absolutely no instructions come with this product, in fact you even have to assume the black wire is the ground. Do your research on how and where this installs before you buy. installing a 20 watt 8 ohm resistor in line to each light may be easier. I have a 05 CBR600RR and I had to splice into the wires that goto the instrument panel. But in closing, if you dont mind the install it is a good product.
I have LED's at all 4 corners on my Honda RC51 and this is a simple 2 wire install that fixed my retardedly fast blinkers in 5 minutes W/O having to add dangerous in-line resistors!
Great product the only catch will not come with oem conector so you will have to get some wire connectors and do a little modification make sure you look up your original relay will tell you wich one is power and wich one go for the lights install on 5 minutes top if you got the right tools.
This is the best product on the market to slow down the flash rate on motorcycles. Its price and quality makes it the number choice.