Lockhart Phillips Bracket LED Turn Signals

$39.99
3.70 out of 5 stars
 
Black/Amber
Black/Amber
  • Description
  • Reviews (6)
  • Q&A (3)
  • LP's surface mounted LED Brackets offer high visibility while replacing plate-mounted screws.
  • Available in amber or clear lenses.
  • Patented design.
3.7 out of 5 stars (6)
3.7 out of 5 stars
5 star   1
4 star   3
3 star   1
2 star   1
1 star 0
See Terms and Conditions
1-6 of 6
Overall 2 out of 5 stars
Location: Socorro, NM
Justice1979
Great idea - poorly made

I bought these about a month ago. Great idea, but made very poorly. While installing the first stud broke off. The other day I was doing a pre-ride check and another stud was broke off... Dont waste your money! Maybe another company will take the time to make these right.

Overall 4 out of 5 stars
Location: Keller, Texas
Spyderider
Good for the price

I instaled this on my Spyder, after doing some work for the cables it worked very well. Only downside in that the plastic should be glue better, had to re glue one side.

Overall 3 out of 5 stars
Location: central jersey shore
badfish
Needed some DIY

once I'm done with it, this product will be great. the set I got did not seem to have the circuit boards secured inside the plastic housing. this gave me a nasty rattle. fortunately, the housing is easy to dis-assemble (be patient doing this). i will use clear silicone to stick the board to the back of the housing, and silicone the housing closed. good product, made better.

Overall 5 out of 5 stars
Location: redondo beach ,ca
Randy
Nice turn signals

bought to replace turn signals that i kept hiting with my leg,cleaned up rear end work great ,looks much better on my ducati monster

Overall 4 out of 5 stars
Location: roanoke, va
ronsbike06
Cheap

cheaply made look ok on bike if you can mount them without cracking them open. have already removed them from my bike and replaced.

Overall 4 out of 5 stars
Location: Marquette, Mi
UPR1
Good signals

I used these on a custom made "rounded" licence plate bracket. They are bright at night and OK during the day. Bolted up fine and fit well. The only problem I ran into was becasue my plate was bent to fit the bracket, the signals had to support more load and were trying to seperate the plastic cover from the base. A little bit of epoxy fixed that issue. If you are mounting it on a flat plate, you will never run into an issue. Make sure you use threadlock so you don' t need to tighten up the bolts too much.

1-6 of 6
Total Questions (3)
Questions with answers:
  3
Questions without answers:
0
Lipper7
josh6787
1-3 of 3
Lipper7 1 year 3 months ago
Are they DOT approved?
MotoSport Staff Expert
1 year 3 months ago Location: Portland, OR, USA
MotoSportRyanT
Unfortunately, Lockhart Phillips does not specify that these would be DOT Approved turn signals. Normally for turn signals to be DOT legal they just need to be a certain distance apart from each other. I would recommend checking with the Department of Motor Vehicles in your area to see if there is any information they can give your on the laws pertaining to street legal motorcycles in your area.
josh6787 Over 6 years ago
Are these sold in pairs?
MotoSport Staff
Over 6 years ago Location: Por+land
Drewski
Yes, these are sold as pairs.
LexSpoofer Over 6 years ago
Do the clear lenses have yellow LEDs?
MotoSport Staff Expert
Over 6 years ago
Darren977
Yes, these clear lens turn signals have amber LEDs.
1-3 of 3