For a limited time, purchase a Bell Revolver EVO Helmet and get an additional FREE Bell ClickRelease Face Shield! MotoSport.com makes it easier to get the helmet you need with the shield flexibility you want!
The Bell Revolver EVO Helmet - Rally:
Bell locked their R&D team in the laboratory and didn't let them out until they had taken the Revolver helmet and turned it into a truly class-leading modular worthy of the Bell name. When the engineering team finally emerged, the result was the Revolver EVO. With improved features like a redesigned eyeport seal, new chin curtain and an improved flip-down sun shade, the Revolver EVO has truly taken Bell modular helmets to the next level.
Lightweight polycarbonate / ABS shell.
ClickRelease for the fastest, easiest, tool-free shield swaps ever.
NutraFog II superior anti-fog, anti-scratch and UV-protected shield.
Velocity Flow Ventilation system with FlowAdjust.
Drop-down sunshield offers "on-the-fly" protection from the sun.
Removable and washable interior.
Exclusive Magnefusion magnetic strap keeper.
Chin curtain to prevent cold air from entering the helmet.
Padded chin strap with D-ring closure.
Weight: 1750 grams.
Industry-leading five-year warranty.
Note: Ships with Clear shield.
The FREE Bell ClickRelease Shield:
Replacement face shield for Bell Star (2015 models and earlier), Vortex, RS-1, Revolver and Qualifier helmets.
3Mode shield for instant on-bike shield adjustments, and ClickRelease for the fastest, easiest, tool-free shield swaps ever.
Features Bell's exclusive NutraFog II anti-fog, anti-scratch and UV-protected coating.
Race versions have posts for tear-offs (tear-offs sold separately).
Note: Compatible only with Bell ClickRelease shield system.
Bell's 3Mode Shield allows for one-finger toggling between Lock Mode, Friction Mode and Crack Mode. Lock Mode is the shield's firmest and quietest setting. It not only locks down the shield, but pulls it tightly to the gasket, creating a water-tight seal. The Friction Mode allows the shield to be freely adjusted from fully closed to fully open and anywhere in between. Crack Mode disengages the shield from the gasket and lifts it about 1/4" to help prevent fogging, a particularly useful setting at stop lights. A quick touch of the 3Mode Lever brings the shield back into Lock Mode.
ClickRelease was designed for the quickest, easiest shield swaps ever. To remove, simply fully open the shield and depress the ClickRelease Triggers. For installation, just align shield pivots in the fully open position and push until they click into place.
1. Measure your head size. To do this, pass a tape measure horizontally around your head at a height of about one inch above your eye brows. When done properly, you will have measured the largest part of your head.
2. Check your measurement with the helmet sizing chart and select the closest size. As the helmet may not always meet your head size exactly, and your head measurement may fall between two sizes, first try the smaller size.
WHEN YOU RECEIVE YOUR HELMET
1. Expand the helmet opening by pulling outwards on each chinstrap, and slide your head into the helmet. If you are unfamiliar with helmets you may be reluctant to pull the helmet down, as it may feel too tight. Even if the helmet is difficult to put on, please use the smallest helmet possible. The helmet should feel snug. If the helmet is not tight, it is too big for you. New helmets will break in and loosen slightly over time.
2. Once the helmet is on:
Check that the helmet inner lining fits snugly all around your head.
Check that the top pad presses on the top of your head.
Check that the cheek pads press up against your cheeks. When you open and close your mouth, you should drag your teeth along the inside of your cheeks.
Check to make sure that you cannot easily slide your finger into the helmet along the side of your temple.
Hold the helmet with one hand on each side. Without moving your head, try to move the helmet up and down, and side to side. You should feel the skin of your head and face being pulled as you try to move the helmet. If you can move the helmet around easily, it is too big. Try a smaller size. Please note that during this check, the chinstraps should be properly fastened.