Competition Werkes Rider Footpegs

$21.77 - $54.99
3.40 5 8
3.40 out of 5 stars
Competition Werkes Rider Footpegs
Competition Werkes Rider Footpegs
  • Description
  • Reviews (8)
  • Q&A (2)
  • Fitment
  • CNC machined from 6061 T-6 billet aluminum; replace stock footpegs.
  • Lighter than stock, slash cut for greater ground clearance; have machined, not knurled, grooves for better grip.
3.4 out of 5 stars (8)
3.4 out of 5 stars
5 star   2
4 star   3
3 star   1
2 star 0
1 star   2
See Terms and Conditions
1-8 of 8
Overall 5 out of 5 stars
Location: Hollister, CA
A Perfect Fit

These Moto GP foot pegs are easy to install, look nice on my ZX-6R, very strong when standing on them, low priced and don't break when you drop your bike. OEM parts are made cheap, cost 55.00 a pair and break easy.

Overall 1 out of 5 stars
Location: Atlanta, GA
Does Not Fit!!

This product DOES NOT FIT my 2006 Kawasaki ZX6R. After unpacking them I had to whip out my grinder and grind down about one quarter inch off each peg before they could fit. Them after modifing them and finally getting them to fit, they did not look good so now they live on my garage shealve. They were a waste of money.

Overall 3 out of 5 stars
Location: Malvern, PA
Look great but do not fit.

Right out of the packaging the foot pegs are really great looking pegs. The problem however is that the hole's diameter is not large enough, so right out of the package they are pretty much useless unless you want to use them as a paperweight. I had to go out and buy a 12.2 mm drill bit (a 12.1 mm probably would have worked but I couldn't find one) and enlarge the hole. Once enlarged they mounted up very easily although the left side peg doesn't seem to sit and the same angle as the right one.

So overall, they look great, but I'm not sure they are worth the effort of making them fit. If Competition Werkes ever got around to trying to mount them themselves and they would make it so they mount up properly then I'd give this product five stars; however, as it is, I can only say three stars and that's being generous.

Overall 1 out of 5 stars
Does not fit out of box!

Although the parts look great when you take them out of the package, upon attempting to mount them you will find that the hole in the pegs is not 12mm which it needs to be, it is in fact slightly smaller so the mounting pin does not fit. I had to buy a 12mm drill bit, then drill out the pegs on my drill press in order to get these to fit. Mounted up they look really nice, it was just much too much work to mount a set of pegs which should have been a no-brainer.

Overall 4 out of 5 stars
Location: Arlington, WA

Overall 5 out of 5 stars
Location: NC
Almost fits

Quality of product was as expected, overall apperance was good. The only issue was some minor grinding was required to fit my '05 Kaw 636.

Overall 4 out of 5 stars
Location: El Paso, Tx
Hott purchase

this peg has good grip.

Overall 4 out of 5 stars
Location: la, ca

1-8 of 8
Total Questions (2)
Questions with answers:
Questions without answers:
1-2 of 2
scottg76 Over 6 years ago Location: Ft. Myers Fl,
Does it fit an 09 R6 also?
Expert MotoSport Staff
Over 6 years ago Location: Portland, OR
Solo Over 7 years ago Location: Tennessee
Will these fit on stock rear sets?
MotoSport Staff
Over 7 years ago Location: Portland, OR
Yes these will work on stock rear sets
1-2 of 2